EMO4000JSS01 General Electric Microwave - Instructions

I removed a few (6) screws and disengaged the motor. Removed the parts and installed in reverse order. Replaced the screws. Easy

Cleaning up the grease from cooking for years on the stovetop below took WAY longer. But the repair was simple!!

removed electrical wires, unscrewed holder, inserted holder, attached wires, added bulb, and put cover back on.

Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.

Odered replacement

The halogen light bulb took a little skill. The prongs were a little difficult to maneuver into place.

Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.

Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube

GE microwave displayed the message that Charcoil Filter needs to be changed. I disconnected the unit and removed the top two screws then removed the top panel by sliding it gently to the left. Replaced the filter. And positioned it in the same way the old filter was installed. Replaced the top panel and screws, Connected the unit back and used the Menu option to reset the Charcoil Filter warning option.

Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

Small sized phillips screw driver was required. Once gaining access to the new motor the part(s) replacement was simple.

Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door

There where five screws to remove to get the bottom off then two to release the motor from the housing pull the electrical supply cord out then reverse the process. Piece of cake.

My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.

Took out the door to be able to replace the door latch. After removing the plastic cover it was challenging to remove the broken latch (unlike other models this has two separate latches individually controlled by spring. The pin holding the latch was impossible to take out and I figured I need to take out inner layer of the door frame (metal part) to remove it. But the frame was stuck and did not come out. I found no reference how to do it on internet and then with another pair of hand pulled outwards while simultaneously pulling upward. Was finally about to pull just enough and replace the latch and push the metal frame to fit back.

Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.