JVM3670WF05 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MABEL from GILROY, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable would not turn
took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.
Great service from PARTSELECT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRUCE from MONROE TWP, NJ
- Parts Used:
- WB06X10144
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
part was cracked
removed old part and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from LEWISTON, MI
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The center of turn table broke. A small plastic part that goes under the glass in center.
We took out the broken part, it came right out,and put new part .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from MAYSVILLE, GA
- Parts Used:
- WB24X830
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would run but not heat
Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from PORTSMOUTH, NH
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn Table Stopped Working
Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Placentia, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy turntable. (grinding)
Nice. Half dozen screws drops the bottom, 2 screws on the motor, pop in the new, reassemble and throw in the popcorn. (Was skeptical. Have replaced quite a few of these little motors in data centers. Common part in high-speed printers. Never saw one fail like this but your feedback convinced me otherwise.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Blakely, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My turntable stopped working
I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgina from WAYNE, NJ
- Parts Used:
- WB06X10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace plastic ring in microwave
placed plastic ring under glass rotating plate in microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from franklin, WI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cooking tray would not rotate
ha to remove the bottom ,to get at the internal screws that held the drive motor. after disconnecting the power to the moter, i removed the two screws that held it in place. i installed thre new motor , reconnected the wire plug to motor . replaced the outer screws, and the project was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecil from Gilbert, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave cooking tray stopped turning
Unplugged microwave from the wall. Removed the screws on the bottom of the oven. Detached the light, removed the bottom panel. Unscrewed one more screw on the turn table motor and twisted to remove. Plugged in the new one and reattached the Electrical wires and bottom panel. Piece of cake. Just don't forget to reconnect the lights!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from las vegas, NV
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rotary dish tray would not revolve
Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Youngsville, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy Glass Cooking tray
The Glass cooking tray was very noisy. This was verified by turning off the tray rotation.
1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!
1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bronston, KY
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drive motor failed
I removed the screws (7) around perimeter of bottom. Don't remove the middle screw as it holds some gizmo in place. Dropped down hinged bottom. Removed motor (2 screws and a plug) matched to picture on website and ordered.
2 days later, part arrived, installed, good to go.
Bill, Kentucky
2 days later, part arrived, installed, good to go.
Bill, Kentucky
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Schoolcraft, MI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turn table would not rotate
As in other postings, remove six screws on the bottom of the microwave, disconnected the the plug,unscrew two screws to remove the old motor...(it took longer to get the new part out its box then it did to make the repair) unpacked the new part, put in the two motor screws, put in the six screws to hold the microwave bottom in place and waalaa...done!
Thanks,
Hank
Thanks,
Hank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Molino, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass turntable stopped turning
Removed five phillips head screws. Dropped metal cover of microwave. The cover is on hinges and will stay up on its own. Removed two screws holding old motor. Replaced with new motor and replaced bottom cover of microwave. Extemely easy repair.
Was this instruction helpful to you?
Thank you for voting!