JVM1870CF06 General Electric Microwave - Instructions

Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.

Use a small screwdriver to depress the flexible clip on the side of the old holder while you wiggle it out of its hole. Gently hammer down the edges of the hole so that the surface is flat. This will make for a tighter fit when you snap the new holder into the hole. Just slide the new piece into position and the job is done.

Per instructions on part select.com website. But needs further repair because still doesn't heat food and pad is partially disabled.

Had to pry the front top of mircowave open and bend down and force this carbon filter in on an angle .Had to call several numbers for instructions. Very awkward and ridiculous to put carbon filter in-besides, it should have come with one to start with!!

Used screw driver to pry plastic ring on inside of door, around the perimeter, loose. It pulled out very easily. Used screw driver to remove attachments to handle, 2 screws. removed the door from hinge, Used screw driver to pry latching tabs on bezel off of the attachment points on the door. Pressed new bezel on, snapped into place like butter. Put handle screws back in, reattached the door to hinge, pressed inside ring back into place. Much easier than this description.

I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!

Open the box that the part came in and place it in the microwave. The best is how fast it came to my home. Thanks

After finding the parts I needed on partselect.com I used a screwdriver to pry DOOR C from the microwave door. Using a screwdriver I removed the door's handle and then using my hands I was able to remove DOOR A. I slid out the glass to the door. It was so easy I then ordered the parts from partselect.com. I screwed the handle onto DOOR A, cleaned the glass and slid it into place and popped it onto the metal door. I then pressed DOOR C into place and was finished in less than 10 minutes.

The new turntable shipment was super fast!!! I received it only a few days after ordering it. Installation was nothing more than placing it in the microwave oven.

GREAT Transaction!!! Thanjs!!!

just set the glass turntable in and bingo it worked
no tools needed. thanks for such a fast delivery
sincerly dennis and chris delbello

Went on line to find repair procedure which was not obvious just from viewing the oven door. Used putty knife to gently pry off inner frame to get access to holding screws.

Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware

Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

Disconnected power cord from receptacle. Removed 5 screws in bottom panel and allowed it to swing downward on rear hinged edge. Disconnnected power wires to motor. Removed screw to detach motor. Inserted coupler through hole beneath center of turntable. Inserted motor shaft into coupler and re-attached motor. Connected power wires to motor and then closed the bottom panel and re-inserted the 5 screws.

I removed 4 screw from the under carriage of the microwave then, removed the 2 screws from the motor, replaced the motor and replaced the screws. It was so easy it took only 4 minutes to perform, better than replacing the whole unit (microwave) and less expensive too. i only wish it was made in the US, I wouldn't mind to spend a little more.