JVM3670WF08 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Nashville, NC
- Parts Used:
- WB27X10810
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
miccrowave would not run.
removed housing. saw t-stat was burnt. replaced t-stat by removing mounting screw and installing new t-stat. reinstalled mounting screw. reinstalled oven housing. 15 minute job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- V. J. from Peoria, AZ
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable no longer would turn
This is the second time this happened for me. The shaft for the Coupler breaks and will no longer let the plate turn. I looked at the instructions of letting the bottom of the microwave down, etc. and all I could think of is I don't think so. I used the tweezers to try to get the broken piece of the coupler but neither time was it intact. Could not locate the broken part so took the liberty of just putting the new part on the shaft, pushed down and viola I now have a turning table again. I am an 83 age female who likes to try being a do-it-your selfer. Of course there are times I am not successful but. . .By thinking back of why this part keeps breaking I think it may be my fault. I always turn the glass plate around manually when the handle of the cup or mug is out of reach. May be my fault and maybe not. Anyway this time I ordered 2 of the same parts just for future repair hopefully not needed. V.J.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Mt. Vernon, IN
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The turntable coupler broke off the shaft
Once we noticed the turntable not working I removed the piece and noticed it was broken at the base of the coupler, took a vacuum and removed the broken piece and installed the new part. Thanks for the help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Dublin, OH
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray broke
I laid the new tray in the microwave. There was nothing to really install....but, the woman I spoke to in order to order the tray was terrific and I had the part in two days!! I would recommend this company every time!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Smithfield, RI
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken coupler
simply remove broken coupler and install new coupler. no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Newbern, NC
- Parts Used:
- WB06X10436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
change microwave fan discharge from front to top
damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juli from San Diego, CA
- Parts Used:
- WB27X10810
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to the microwave
Trouble shot first by removing the digital read out face plate panel, lifting it up and out. Found the thermostat housed on the bottom section (found a picture of what I was looking for). It had two connectors. Removed the connectors and noticed that the one looked burnt/melted that was on the thermostat. Took paper clip, connected it with the wires to bypass the thermostat. Plugged in the microwave and power returned. Yes! Ordered thermostat part and changed it out. The new part didn't have a piece that fit exactly into the floor of the microwave so I just made sure it was secure to the bottom. It is only attached by 1 small screw. Fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Effingham, IL
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass turn table coupler (drive) broke - no table turning.
Lifted off the glass turn table and just pushed the new plastic couple onto the drive post. The plastic coupler is splined, so just sit it onto the drive post and lightly turn it until it starts to drop and give a little downward push. That's it - about 30 seconds and the table is turning again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MANUEL from ESCONDIDO, CA
- Parts Used:
- WB27X10597
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
diode burnt
it was a simple screw in on both ends. no soldering
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from West Chester, PA
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing Coupler
When we moved into our recently purchased home, I noticed that the turntable in the microwave wasn't turning. I discovered that the coupler was missing and hoped that nothing else was damaged and that getting a new one would fix the problem. I ordered the part and it came the very next day, even though I got 3-5 day shipping. Didn't even have to unscrew anything to install it. It popped right in and the turntable works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Otsego, MN
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
coupler broke
removed the bottom of the microwave and removed the motor and replaced the coupler and reassembled. Easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from San Diego, CA
- Parts Used:
- WB02X10753
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Metal flap would not close.
My son fixed it in less than five minutes! easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Chester, VA
- Parts Used:
- WB27X10810
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to Microwave
Microwave would not turn on--No lights--Nothing worked 1. Removed screws from back and side and pull off microwave cover. Be careful! There HIGH voltage back there due to a large capacitor that stores power. This capacitor is charged up even with Microwave unplugged. I checked the fuse located on top back part of Microwave. A lot of the time this is the problem but this time the fuse was good. I used an Ohm meter to check to see if there was an open circuit in one of the Thermostats. There are two of them in the Microwave. The Thermostats are about the size of a dime. One is located on the top right side and the other is on the top left side. One of them was bad. I ordered a new Thermostat. It arrived in just 2 days. I installed it and the Microwave was repaired and working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from terlingua, TX
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
couper on turntable had broken into.
took part of put new part on.30sec to do.
Was this instruction helpful to you?
Thank you for voting!