JVM2050WH02 General Electric Microwave - Instructions

I took current readings between the magnetron and the HVT and saw that there was not current draw. I ordered the magnetron replacement and installed it. We can eat leftovers again!

Took the door apart and replaced defective parts

I laid the new tray in the microwave. There was nothing to really install....but, the woman I spoke to in order to order the tray was terrific and I had the part in two days!! I would recommend this company every time!!!!!!

First, unplug microwave. Unscrew two screws at top of microwave, slide grill cover left and remove. This allows access to single screw holding control panel. Remove this screw and lift up control panel to remove. Secondary door switch is black switch at lowest position. The switch is held in place by a lever in back and very hard to get to. Remove the wires plugged into the switch, then remove two screws holding the plastic switch mount that holds all three switches. These screws use a "star" type screwdriver. Once the plastic mount is free, lift it up, right, and tip it slightly to find the lever that will release the black secondary door switch (the lowest switch)...release the broken switch, snap the new switch in its place. Replace the plastic mount by lifting and replacing back into position and replace the two "star" screws. Now, replace the wires onto the new switch, and test operation. Replace control panel, and top grill. It goes faster than it writes...getting the old switch out through that difficult to reach lever was the hardest part...still less than thirty minutes.

It was great...Thank you for having the part available...

Rec'd the parts within a day or two after ordering and simply placed them where the old ones were removed and wala my stove is back filtering. Only problem, the oven won't ignite while the broiler and stove top burners are fine. Go figure.

We put the new glass lens in the metal frame and screwed the frame in under the microwave. Easy, breezy! Like new condition!

Removed old film. Put new film on using plastic scraper to smooth and remove air bubbles.

At first I thought it was just the bulb, but I wasn't able to find a video of the exact model. The dificult part was figuring out how the vent housing came off (turns out it slid to the left then lifted out) but after I figured that out, replacing the cable assembly and the bulb was really easy.

Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.

Just pull down on "O" ring tab and filter will release. Install new filter in same position. you may have to pull on "O" ring to complete fit.

There are five Philips screws on the bottom outside cover .one at each corner and one at the front center. Remove all four at the corners .leaving the front center for last. When the last screw is removed ,the cover will hinge down, it is attached to clips at the back that allow it fold down. The wire attached to the light socket is connected by a pull apart plug. Grasp at each end of the hard plastic connector and pull outward ,DO NOT PULL ON THE Wires ! Lift the cover from the back of the microwave place it on a flat surface on a towel keep it from sliding around. Remove the screws holding the porcelain sockets. Reverse procedure to reinstall .Installing new Halogen lamps is suggested. Use a clean tissue or cloth to handle the lamps, finger prints on the lamp will shorten the life .

R/R worn turntable coupler.

Loosen the two long anchor bolts that screw into the top of the microwave cabinet. These are usually in a shelf or cabinet directly above the microwave. Tilt the microwave forward enough to remove the 2 Phillips head screws from the top of the microwave cabinet. They are near the front. When these two screws are out, remove the fan vent. Once the fan vent is off, remove one screw that holds the control pad in place. Let it hang down. Just to the left of the control pad, you will see wires leading to three switches that close when the door is closed. Use a torx driver to remove the two screws that hold the switch bracket in place. With the bracket out, unplug the wire harnesses. On the opposite side of the wiring connected, a tab holds each switch in place. Lift the tab and slide the switches out. Usually, the bad switch will be identified by a loose or broken spring. Test them by pressing down on the switch. If you notice the bad switch spring, this is usually the bad one. When you have the new one, simply push it back into the appropriate slot and be sure that the holding tab snaps back in place. Plug the wires back in and re-attach the bracket. Put the control pad back on, then the fan vent. When down with those, push on the bottom of the microwave to lift it back into place and tighten the two anchor bolts in the top.

Remove old film by peeling away from glass. Lift from corner and pull to remove. Remove backing from new film slowly as you are applying to the door a little at a time. Smooth with a plastic spatular as you apply from one side of the door to the other and you will have no wrinkles or air pockets.