Models > JVM2070BH01 > Instructions

JVM2070BH01 General Electric Microwave - Instructions

Jump to:

All Instructions for the JVM2070BH01
91 - 105 of 155
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Tommy from Santa clarita, CA
Parts Used:
WB36X10071
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Previoous glass lens was broken
This repair was easy and could be done by anyone. If you undertake to do this replacement, remember to slowly bend the medal tabs back that hold the lens. Handled roughly these tabs could break off.

This repair can be don in under 5 minutes, easily !!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from Avon, CO
Parts Used:
WB07X10722, WB01X10246
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
broken part
Replaced with new part
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Marine on St Croix, MN
Parts Used:
WB07X10722
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Frame broke in several places. It had been assembled inncorrectly at the factory.
Took pictures of broken frame before removal. Parts from the old frame had to be used on the new frame. Replacement was straight forward and not difficult.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from Marana, AZ
Parts Used:
WB36X10071
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken light lense
Removed one screw, installed new lense in lense frame, rescrewed. Done.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joe from Pomona, CA
Parts Used:
WB07X10722
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The vent grille frame was broken. How? The vent was loose and not operating properly .
Removed the screws holding the frame to the microwave and all the screws holding the front stainless vent part. Reattached the vent to the new plastic frame and microwave. I only used a screwdriver.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Warren, MI
Parts Used:
WB36X10071
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken lens.
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Shawnee, OK
Parts Used:
WB24X829
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
time would count down but unit would not run & heat.
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edwin from New York, NY
Parts Used:
WB27X10928
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
No heat
Replace the fuses
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lucinda from Burke, VA
Parts Used:
WB49X10063
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
dropped the glass cooking tray while cleaning
after a couple of misfires, got the correct size tray, and replaced it in the oven.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mack from Jacksonville, FL
Parts Used:
WB27X10928
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Hugh from Slippery Rock, PA
Parts Used:
WB36X10071
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
glass light lens were broken
All one has to do is use a screw driver to remove the screws, one per lens.
Then lower the lens bracket, bend the 4 tabs holding the
lens, remove and replace the lens and screw the brackets back in place.

Less than 10 minuits.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Shawnee, OK
Parts Used:
WB24X829
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven wouldn't heat
remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.
3 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clarence from Rocky Ridge, OH
Parts Used:
WB24X829
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
When opening door the microwave would turn on.
Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.
Was this instruction helpful to you?
Thank you for voting!
Customer:
mikael from Brooklyn, NY
Parts Used:
WB08X10027
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Microwave Interior Lamp Went out
At first I thought it was just the bulb, but I wasn't able to find a video of the exact model. The dificult part was figuring out how the vent housing came off (turns out it slid to the left then lifted out) but after I figured that out, replacing the cable assembly and the bulb was really easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Julie from Elm Grove, WI
Parts Used:
WB24X829
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Microwave fan would run when opening the door. Evenutally the mircowave would not run, but the electrical panel was still working
Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JVM2070BH01
91 - 105 of 155