EMO4000JWW02 General Electric Microwave - Instructions

Remove two screws on the top of the grill. Slide the grill to the left and then pull straight off. Slide the filter in place. Replace grill and screws

I first read the previously posted directions from other customers that were sent with my part order confirmation, which were all very helpful. Then, I basically used a screw driver to unscrew the screw holding the lens cover in place - be careful as it is a very tiny screw and it can easily fall behind your oven. You might want to place a large piece of cardboard over the space between oven and wall, as I did, so that you don't lose the screw in case it falls. Next I pried open the prongs, carefully slid out the cracked lens, and slid the new lens in place, pushed back the prongs and put the screw back in. I found that it was easier to use my fingers to first place and tighten the screw because it is very small and will keep falling out of place if you try to just use the screwdriver. Good luck!

I ordered and replaced the coupler. Once installed, all was well!

ordered 2 new sockets and bulbs easy replacement great service from this site

It was very easy to remove the old charcoal filter and insert the new charcoal filter(had done it before with with the replacement filter GE had included with the purchase).

Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

.Thank You Dan

Removed the 6 screws that held the cover below my microwave. Unplugged the part, plugged in the new one and I was done. My part arrived from you just one day after I ordered it! It was my first microwave repair ever, and it couldn't have been easier.

I followed the directions on your web site. I removed the screws adn dropped the bottom tray, unplugged the drive motor, removed two screw, and replaced with the new motor. It only took about 15 minutes.

Wow! It really was as easy as everyone says. I ordered the part. It came overnight. I took out the 6 screws on the bottom of the microwave (AFTER unplugging the microwave of course), unscrewed the part and unplugged it, put in the new motor, plugged it in and screwed it in, and replaced the bottom screws. The only trouble I had, which really has nothing to do with this part or the repair, was that some of the screws on the bottom of the microwave were very difficult to replace as they didn't seem to line up with the holes beneath. I had a handyman coming to do some deck repairs and had him put those in. Ah well. I did MOST of it myself.

Stephanie, age 52

I went to your site and looked up the schematic parts list and determined how to remove the grill and install the filter. I had the grill off and when the filter arrived I put it in, replaced grill and screws and then in about 20 min had the microwave installed on the wall and operating. By the way the part arrived about three days earlier than estimated. Thanks for your prompt response. You are on my favorites list for future appliance parts.

I removed the screws that held the bottom in and then dropped it down to access the motor. I removed the 2 screws that held the motor in and unplugged it. I then plugged the new one in and reattached it with the 2 screws and put the bottom back on. It took me about 5 minutes to fix it for only $40.00.

I placed the glasstop on the sprocket

Simply removed screw, pulled down light holder, unfoled the metal tabs, took out the broken pieces and replaced the glass lens and light bulb.

I turned off the breaker/electric power to the microwave; opened the base of the microwave, detached the wire to the old drive motor, removed the
screws holding the drive motor in place; removed the old drive motor and installed
the new drive motor---beyond easy!!!

Thank you!