JVM1661CB004 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald L from Shafer, MN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
This was so easy. I'm really glad I did not call a repairman!
Removed six screws that allowed the "bottom" to swing down; then removed the two screws holding the motor - disconnected the two wires. Installed the motor and reversed this procedure to finish the project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cory from Galesburg, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable / cooking tray not rotating
Let me keep this short and simple.
Disconnect the power to the microwave
Remove the (7) screws from the bottom panel
Disconnect the wires from the old Drive Motor
Remove the retaining screws of the drive motor
Then install the new drive motor in the reverse order
Disconnect the power to the microwave
Remove the (7) screws from the bottom panel
Disconnect the wires from the old Drive Motor
Remove the retaining screws of the drive motor
Then install the new drive motor in the reverse order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Vidalia, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable did not operate properly
took 6 screws out of the oven bottom
removed 2 screws that held the motor
diconnected the power plug.
plugged in power to new motor, replaced 2 screws that held it in place, replaced 6 screws that held bottom of oven
That was it...
removed 2 screws that held the motor
diconnected the power plug.
plugged in power to new motor, replaced 2 screws that held it in place, replaced 6 screws that held bottom of oven
That was it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Sparta, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the glass cooking tray would no longer move.
We removed the vents from under the bottom and then the 4 screws and pulled the motor out. It was a no brainer to fix and the part came in alot faster than expected.
Thank You
Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbarba from Tamaqua, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable would not turn
took screws out of bottom of microwave.dropped down bottom cover to get at drive motor I took out one screw droped down cooking tray motor disconnnected 2 wires reconnected put back up and put 1 screw in ,fastened bottom and was fixed very easy ,and parts select is the best place to find what you are looking for if I ever need parts this is where I will order from service is great and only took about 2 days to receive my part .I went to store where I bought my microwave and they wanted to sell me a new one.saved over $200
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from GRAND BAY, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Glass Cooking Table Not Turning - Food Burning
Most mirco wave have a plate on the bottom to protect turn table motor. This one had no screws - it has 6 tabs holding the protective cover. Used pliers to tear tabs. Used philip's driver to remove screw and turned motor to come out. Went back in reverse order replacing motor. Left protective plate off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Olathe, KS
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable would not turn
Removed five screws from the underside of the mircowave. Disconnected the two prong plug in. Removed the one screw that held the motor and replaced with new motor. Reconnected the plug and replaced the five screws
Tested the result with a bag of microwave popcorn. Worked perfectly.
Tested the result with a bag of microwave popcorn. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sam from edmond, OK
- Parts Used:
- WB06X10224
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken rack holder
removed the damaged / broken rack holder. inserted the new rack holder.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MANDEVILLE, LA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it broke after 3 days and i was denied a new part or refund
it was easy . i unsrewed 2 srews and it went right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from oak lawn, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
G.E. microwave turn table was loud and not working
I took it apart and found a small electric motor was not working . I couldn't find it locally so I ordered it from partselect and it was here in just a few days.the repair was easy only a few screws and plug it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Tucson, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray stopped rotating
I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Highlands Ranch, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable quit working
Took the bottom of microwave off unplugged motor replaced it with new one (two screws) plugged it in replaced bottom and ther you go saved $240.00 over the local appliance repair company. Thanks Mike,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MABEL from GILROY, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable would not turn
took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.
Great service from PARTSELECT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from PORTSMOUTH, NH
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn Table Stopped Working
Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Molino, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass turntable stopped turning
Removed five phillips head screws. Dropped metal cover of microwave. The cover is on hinges and will stay up on its own. Removed two screws holding old motor. Replaced with new motor and replaced bottom cover of microwave. Extemely easy repair.
Was this instruction helpful to you?
Thank you for voting!