JE1860CB01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kirsten from Menifee, CA
- Parts Used:
- WB49X10135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken microwave tray
I'm very impressed with the quailty of the product and the shipping speed. I had the new microwave plate in 2 business days. No difficulties with installation, obviously.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from PAWLEYS ISL, SC
- Parts Used:
- WB24X26575, WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Microwave was accidentally overheated and all power was lost.
Since I didn't know if it was the current fuse or the flame sensor, I ordered both parts, and, I had to order the tamper proof torx bits needed to remove the microwave cover ($7.45 on Amazon). Once the cover was off the unit, both parts were easily accessible on top of the oven and were replaced in only a couple of minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Plano, TX
- Parts Used:
- WB26X10056
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The revolving motor would not turn the glass tray
e.g. First I removed the bottom cover. I then removed the two screws that hold the motor in place. I then pulled the motor out about 3 inches and disconnected the two wires...)
I then put the new motor in with the two screws and hooked the wires back up. I then replaced the bottom cover and put the the turn rack and glass tray back in place. Works great.
I then put the new motor in with the two screws and hooked the wires back up. I then replaced the bottom cover and put the the turn rack and glass tray back in place. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Greenville, SC
- Parts Used:
- WB26X10056
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The turntable move intermitently and made a lot of noise.
Once I unpluged the unit and laid it on its back, I remove four screw and exposed the motor. The motor was mounted with two screws and a push on electrical conecter. I reversed the procedure and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mini from Wilsonville, OR
- Parts Used:
- WB49X10135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hubby put in two cold hard boiled eggs in shell to heat and microwave plate bursted.
After picking up the broken glass and cleaning up the mess, I looked up GE microwave turntable plate and came across this site! Easy to order on their website, good price, and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from PIEDMONT, CA
- Parts Used:
- WB26X32629
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
runs but does not heat
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It was easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from PONCA CITY, OK
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Lapeer, MI
- Parts Used:
- WB06X10209
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Roller guide broke where it was inserted
Replaced with new guide. Fits well and works properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from SEATTLE, WA
- Parts Used:
- WB49X10135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken turn plate
It was so easy to order a new glass plate ! Love this web site,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Pearland, TX
- Parts Used:
- WB49X10135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wrong cooking tray in the microwave
Replaced the 16" tray with a 14" tray. Works great now. Took about 20 seconds to take out the old tray and put in the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from MADISON, AL
- Parts Used:
- WB26X32629
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out magnetron
Removed cover
Disconnected capacitor from old magnetron
Removed old magnetron
Installed new part
Connected capacitor
Reinstalled cover
Disconnected capacitor from old magnetron
Removed old magnetron
Installed new part
Connected capacitor
Reinstalled cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kip from POWELL, OH
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heat
-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Bellevue, IA
- Parts Used:
- WB06X10209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stem on bottom of guide cracked and became too loose to drive turntable
It took quite a bit longer to decide which one of the roller guides in the selection was the right one, than to install the new one. Got it right though, works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mathew from Houston, TX
- Parts Used:
- WB55X10270, WB06X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave starts as soon as the door is closed
I replaced the door key, it was broken on the side so it was not touching the sensor for shutdown. Replaced the door key and the backframe keep the microwave like brand new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bart from new sarpy, LA
- Parts Used:
- WB27X11033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Try to heat food and fuse would blow.
Went on Youtube and pulled up how to fix a microwave.
Was this instruction helpful to you?
Thank you for voting!