JVM130K02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Whittier, CA
- Parts Used:
- WB15X309
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Handle broke after 8 years of use
I seperated the trim from the inside of the door very carfully with a putty knife. I removed the two door handle screws. installed the new handle and replaced the trim.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JULIA from JACKSONVILLE, FL
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
microwave would not start
took of cover removed switch and replaced with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemarie from Clark, NJ
- Parts Used:
- WB2X4263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filters were very soiled
Oh just took old ones out and put on the new ones.
The easy and best part was that this Partselect sent the correct order first time and they were very informative and polite.
Nice company i would use the again.
The easy and best part was that this Partselect sent the correct order first time and they were very informative and polite.
Nice company i would use the again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Olive Branch, MS
- Parts Used:
- WB27X1160, WB27X10240
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
blowing 15 amp fuse when hitting power button
Looked at schematic to see which parts became active when the power button was pushed. From there used meter to determine diode was open and capacitor was shorted. Biggest trouble was dis-assembly/assembly required to get to electrical parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Cleveland, OH
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
under microwave (above stove) light
The replacement of the light no problem, the reason the light broke; problem. The original was glued in (for transport i think) and simply trying to unscrew it out (in a very tight slot) it broke; be careful or you’ll be buying a new $20 bulb (with shipping and handling).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Fort Smith, AR
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb burned ot
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Fountain Hills, AZ
- Parts Used:
- WB24X829
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Micrwave won't run - turntable turns backwards when door opened...
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Albuquerque, NM
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Power worked but would not cook
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Frederick, MD
- Parts Used:
- WB15X309
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Door Handle
The repair itself was easy, the difficulty was in removing the cover on the inside of the microwave door. Once I got the cover off, the repair took 10 minutes. The screws sent with the handle were too long and as result I poked a hole through the backside of the handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Yorktown Heights, NY
- Parts Used:
- WB27X10585
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
loud hum & the microwave quit working
remove the housing,replaced the magnetron and reassembled.no problems at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Hanover Park, IL
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave appeared to work. Fan worked, timer worked plate rotated. It just didn't heat the food!
I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GENE from SHREVEPORT, LA
- Parts Used:
- WB27X709
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
MICROWAVE SHUT OFF COMPLETELY
UNPLUG MIRCOWAVE.REMOVE THE HARDWARE, COVERS, AND DECONNECT THE CONTROL PANEL. REMOVE AND REPLACE VENT THERMOSTAT. REINSTALL EVERTHING IN REVERS ORDER. WORK FINE NOW. ADVISE IF YOUR FIRST TIME GET INSTRUCTIONS ON INTERNET SEARCH OR YOU TUBE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from El Segundo, CA
- Parts Used:
- WB24X829
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would turn on when door opened
Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Seaford, NY
- Parts Used:
- WB7X1887
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken exhaust grill on top of microwave that is installed over stove
removed the old broken exhaust grill and replaced it with a brand new exhaust grill....two screws had to be used to hold it in place....PERFECT...looks brand new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Austin, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside Bulb went out.
Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE
Was this instruction helpful to you?
Thank you for voting!