JE740GY010 General Electric Microwave - Instructions

this is not fair to the do it yourself person because I have been an electrican for forty one years I removed the cover spotted the burnt limit switch ordered the part replaced the part and checked operation of the microwave thanks for the painless task of locating and ordering of needed part

I thought I was setting the timer only on the microwave and accidently cooked an empty oven for 10 minutes. It was dead and I used the schematic and figured out the problem. Got the part and installed in 10 or less minutes. Oven is back in action.

Per instructions on part select.com website. But needs further repair because still doesn't heat food and pad is partially disabled.

remove the housing,replaced the magnetron and reassembled.no problems at all

Removed power from unit. Removed 7 screws from cover on bottom of microwave. Unplugged the power connector from the installed motor. Removed 2 screws holding motor. Positioned new motor using small nibs used for purpose of proper positioning. Used mounting screws removed from old motor to firmly fix new motor in place. Installed original mounting screws holding bottom cover in place. Connected power and tested operation.

completly removed outer cabinet,discharged capicator,removed some internal parts so I could get at the magnetron,
.removed replaced magnetron,reinstalled inner parts& cabinet .tested microwave viola
everything worked again.
Thanks, PartsSelect
Ernie

Just open door and install the new cooking tray in the grooves.

Removed outer case, checked fuse first, it was good so went to thermostat. No continuity reading. Unhooked thermostat, used jumper wires to by-pass break—briefly plugged the unit in. It came on so I knew the issue was definitely the thermostat.

Relatively simple for skilled person.

I removed the outside cover of my microwave . ,It slides off , and the the burned out bulb was in a easy location ,and easy to remove, and then I replaced the new one then , replaced the outside cover, pluged in my microwave and bingo '''it was a sucess, and by the way I am 82 years old and like to repair things , so it saved me about 100. 00 With the walk in price of 65. 00. They charge you,, and labor it cost to replace the blub thank you for your promped service pat

it was a simple screw in on both ends. no soldering

I googled "Microwave stopped working", and after reviewing numerous websites with suggestions, I found the response noted below at "Help Owl" which was the most straighfoward and clear explanation to trouble shoot the problem. I first tested the Thermal Cut Out (TCO) per the instructions below and that was the problem. I didn't have to test the electrical fuse. Turns out that you cannot typically use the microwave continuously for more the 12 or 13 minutes or it may overheat and the TCO will shut it down. Extremely easy to test for and fix, and the part is only $15! See Trouble Shooting steps as follows: Make sure that the unit is vented properly and that if you are using it for prolonged periods while cooking, that you turn-on the vent fan.
If there is no display / power within the unit...first check your power source where you plug the unit into the wall.

If that is good, Remove the Cabinette/Cover "Note: it has 3-Torx Anti-Tamper Screws".

Then as you face the microwave from the rear, at the left rear corner is a small circuit board with a fuse. "Check the Fuse"

If the fuse is good, Check the following:

1 - The most common component failure is the "Cabinette TCO" (Thermal Cut-Off Thermostat).

As you face the microwave from the rear...It is located under the cover, on top, on the left front corner area.

It is a Circular, Black & Silver Disc Shaped component about the size of a dime in diameter and is about 1/2" in height.

It has Two (2) Wires attached to it's spade connectors and it acts as a safety fuse.

"IF YOU PUT AN INSULATED JUMPER WIRE ACROSS THE 2 TERMINALS THE POWER SHOULD RETURN AND THE DISPLAY WILL LIGHT"

Anything other than these two items should be checked by an Authorized Service Technician as these microwaves have components thay carry "HIGH VOLTAGE SHOCK HAZZARDS"

I took instant pictures at each step to make sure I put the wires back correctly. Removed the front panel. Discharged the capacitor with a voltage meter. Removed parts in front of the magnetron. Removed and replaced the magnetron. Reassembled. Works find now. Small hands, a flashlight and a magnet (for dropped screws) would help. I did not need the pictures.

Remove cover-the hardest part, as I needed to buy a new set of driver bits that included the dimpled security drivers to remove three screws. GE includes schematic and troubleshooting flow chart with the unit, taped inside the cover. Required more time to look up the part on-line and order it than time used to make the repair.

I removed the cover this required a special star Apex tip witha hole in the center. $10 for a set at Lowes.Replaced the fuse and Thermal cut out at the same time. The oven woks like a charm.I would like to add that GE customer service was no help basically told me that it was a throw away unit. If they built it you can fix it.Hope this helps any DIY breathern outthere.