ZSC2001FSS02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- johnny from port orange, FL
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no power in microwave in turn table wouldn't turn light would work act like door was open
remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Wesley Chapel, FL
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable Stopped Working/Display Timer Would Countdown But Not Heat
With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from ITHACA, MI
- Parts Used:
- WB20X10048
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat quit.
Checked all sensors with a multi-meter, found the thermostat to be the problem, no continuity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Newton, MA
- Parts Used:
- WB36X10130
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken lower glass light reflector
Easy slip in to 2 hinges
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Williamsburg, VA
- Parts Used:
- WB06X10215
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Mica cover protecting waveguide was sparking
The part had to be rotated to fit then screw was replaced. Only tricky thing was that the screw was the security allen type with a small post in the center. Luckily I had a set of them from installing similar bolts on license plates.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Louisville, KY
- Parts Used:
- WB36X10328
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lights were burned
It was REALLY EASY finding the right parts using your diagrams..Thanks for your HELP!!I will definitely be back.Dan H
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rong from Portland, OR
- Parts Used:
- WB20X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
circuit shortage shows, i thing it because i heat on the counter too long cause the thermotart not fumctional.
it work ok now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from New Philidelphia, OH
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would turn on ,BUT turn table would not turn and oven would not heat.
Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Remer from Dothan, AL
- Parts Used:
- WB20X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Could not be turned on
Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Littleton, CO
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Door Interlock Switch Failed
Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Chandler, AZ
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
When trying to run, intermittently, the light would come on but the tray wouldn't rotate or cook. When the door was open, the tray would intermittently rotate.
I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.
Was this instruction helpful to you?
Thank you for voting!