JVM1790BK01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Cumberland, ME
- Parts Used:
- WB06X10655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Previous mica canopy sagged and was breaking apart.
Removed existing canopy by removing two screws and sliding out. Removed small fan assembly and detached brown plastic mount from mica.
Attempted to snap brown plastic mount to new canopy but had problems with it staying in place, even after snapping into holes on canopy. Applied a very small amount of glue to hold it in place and balanced fan assembly on part and slid into place. Re inserted the two screws.
Attempted to snap brown plastic mount to new canopy but had problems with it staying in place, even after snapping into holes on canopy. Applied a very small amount of glue to hold it in place and balanced fan assembly on part and slid into place. Re inserted the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Garden City, NY
- Parts Used:
- WB02X10750
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
rack holder broke off in oven
tried to replace rack holder but was unable. It did not turn easily and took a screwdriver to pry it out before replacing it. No instructions were available from manufacturer so we were afraid if we pried it out we would be severing different entry parts for the rack holder. Not a good scene!!!We finally pried it out but without instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Minneapolis, MN
- Parts Used:
- WB06X10705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We broke the glass plate in the microwave and the rotating ring too
We had an accident on Christmas day, while using the convection option on the microwave, the glass plate and ring assembly slipped down from where it was temporally being stored, and shattered into many pieces.I was really lucky, we had a older GE microwave that we scrapped out. My wife and I decided to keep the glass plate and rotating ring, when we tried the parts it wouldn't turn. I decided to try a new rotating ring considering the glass plate would of cost quite a bit more. When the part came, I tried the ring and as I said I was really lucky, it worked perfectly. The ring from the old microwave made the glass plate sit too high and consequently wouldn't turn. It wasn't really much of a repair, but it all worked out great, the parts site was easy to use and the parts came when they said they would.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Decatur, AL
- Parts Used:
- WB06X10705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one wheel missing on tray ring
took old tray out put new one in. works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from HAMBURG, NJ
- Parts Used:
- WB27X10866
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dim panel lights on Profile Microwave Oven
Repair was easy. I took a picture of the board while connectors were still in their place. That really wasn't necessary because it was easy to match each connector with its receptacle.
On completion, the power was put on and I was disappointed that the repair hadn't worked. The panel lights were still dim and hard to read.
I did a google search on this problem and read that the problem with dim lights is due to a bad condenser and (though I don't believe it) one can go bad in time without being used. I called Parts Select and received a return authorization. The next day to my surprise, the panel lights were now bright and readable. I called Parts select and cancelled the return. Two weeks later it is still working.
Thanks for being a reputable company.
On completion, the power was put on and I was disappointed that the repair hadn't worked. The panel lights were still dim and hard to read.
I did a google search on this problem and read that the problem with dim lights is due to a bad condenser and (though I don't believe it) one can go bad in time without being used. I called Parts Select and received a return authorization. The next day to my surprise, the panel lights were now bright and readable. I called Parts select and cancelled the return. Two weeks later it is still working.
Thanks for being a reputable company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from VIPER, KY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Blown fuse in microwave
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from martinsville, NJ
- Parts Used:
- WB06X10655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The cover over the fan needed to be replaced.
I removed 2 screws that held the fan cover. I pulled the cover off and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ORLANDO, FL
- Parts Used:
- WB25X10019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the halogen light above the stovetop burned out
the online instructions were ideal - just unscrewed the right-hand screw (the only screw) and replaced the bulb by inserting gently but firmly)...getting the old bulb out was a pain, b/c it shattered in my grasp (with little bits of glass all over the stove!), but that has nothing to do with the purchase and installation from this site - all a very good experience
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Lakewood, CO
- Parts Used:
- WB56X10669
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I needed to acquire and install a mounting plate for an over the range microwave
I attached the mounting plate to the wall as directed in the installation instructions which I had downloaded from GE. This procedure took 45 minutes to complete. I was then able to mount the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Colorado Springs, CO
- Parts Used:
- WB02X11096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door latch broke where it hooks to spring.
Just pulled off the cover, removed the old latch, re-connected the spring...put it all back togeather. Everything just snapps back in. The entire repair took about two minutes. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Gastonia, NC
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Lamp burned out.
Removed one screw, removed cover, and replaced lamp. Pretty straightforward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronie from BRIARWOOD, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave does not have power at all, though outlet has power
unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HILTON HEAD, SC
- Parts Used:
- WB02X32720
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
When door was opened, the microwave would turn on.
Looked on line and found a you tube that said to check the door micro switches (there are three of them. Found one of the switches had an actuator that was stuck down. I got the actuator working but problem was still present. Another you tube showed how to repair the contacts in the switch and that solved the problem. however the plastic piece that holds the switches was broken and would not hold the switches securely. Ordered that piece and a new switch. Remove the vent plate on top (one phillips) and the control panel (one phillips). The switch holder is held in place with 2 phillips and is a little tricky to get it out and undo the wires. Once out, it's just a matter of putting the switches into the new holder and reinstalling it. Google the model number and the problem and there's virtually a you tube to repair ANYTHING.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenoma from NORTHGLENN, CO
- Parts Used:
- WB02X11096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Latch was broken you put spring on
Took off plastic around inside the door , took broken latch off and put spring on new latch on plactic on and it works . ????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda sklar from JAMAICA PLAIN, MA
- Parts Used:
- WB49X10176
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Broken glass turntable in microwave
Just placed it in microwave
Was this instruction helpful to you?
Thank you for voting!