PSA9120SP1SS General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anita M from Rochester, NY
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Could not find the part at the big box stores - HD or Loew's
Removed the glass shield and inserted the 2 bulbs. Then replaced the glass shield.
The staff were terrific. Thanks so much as it had a happy ending.
Anita
The staff were terrific. Thanks so much as it had a happy ending.
Anita
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from New Milford, CT
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
interior/exterior bulb replacement
Inside "cavity" bulb was a PITA. Need to remove top decorative trim (2 screws and tabs) to access bulb housing. Broke 1 screw tab so be careful (Wiggle it more). Acccess to bulb housing was made for younger smaller hands, attached by 1 screw. Remove screw, rotate housing, replace bulb. Reverse proceedure. Outside bulb, cake...1 screw, drop lens replace bulb, your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CURTIS from WINDSOR, WI
- Parts Used:
- WB02X35488
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no night light
took out cover by removing cover. pulled out light bulbs replaced with new bulbs. replaced cover and tighten screw. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Palm Desert, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
failed bulb
unscrew one screw and remove bulb and insert new bulb and replace lense with one screw-
as easy as it gets-
as easy as it gets-
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from CUMMING, GA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had to replace to halogen lamps
Repair was simple; only a phillips head screw driver was required to remove the access plate.
Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.
Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Laguna Niguel, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface light bulbs burned out under microwave
Unscrew (one screw) and take off the cover of the surface light under the microwave (the light over the stove). Firmly pull out the old light bulbs. Align the two prongs of the new bulbs into the socket and firmly push into the recepticle. Replace the cover and screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Reno, NV
- Parts Used:
- WB25X10019, WB06X10554
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed New Holder Assembly and bulb
Replaced the cord, attached it to the light fixture, and then replaced the cover for the bottom of the appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxine from Flagstaff, AZ
- Parts Used:
- WB48X10064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No rack in the Convection/Microwave
Just placed the rack in the Convection/Microwave oven and baked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Dennis, MA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
overhead oven light in micro burned out, could not find correct halogen bulbs locally
took of the cover, replaced bulbs then replaced bulbs. One was more difficult to get in than the other but all is ok now. No more stove stop cooking in the dark:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Alpharetta, GA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
3 lights out--1 inside 2 below
the ones below were easy --underneath take out screws--take out old bulb--put in new one--the one inside a little more difficult--but not bad--take off panel on the front of microwave over door--the light is in a metal housing on the right--take out old bulb --put in new--wore rubber gloves putting in new lights--do not want to touch them with your fingers--i just watched the GE video on the parts website and it told me exactly what to do--if i can do it anybody can do it !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Chandler, AZ
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
When trying to run, intermittently, the light would come on but the tray wouldn't rotate or cook. When the door was open, the tray would intermittently rotate.
I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Chantilly, VA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave interior lamp burned out
Unplug the microwave. Remove front grill and cover by removing 2 screws on top of microwave. You have to look down from the top. I could not locate the screws by feel. Once the two screws are out, remove the grill by sliding slightly to the left to lift out. Open the oven door to facilitate removal. Then remove the steel light cover (1 Phillips screw in the center of the unit) and unclip the bulb holder on the right. Do not touch the halogen bulb when you replace. Reseat the bulb holder and test by plugging in the unit with the door open. Unplug and replace the light cover and grill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!