JE730WA01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from The Woodlands, TX
- Parts Used:
- WB27X10985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave stopped working and nothing would show on the display...completely dead. Wife had just heated two separate items, one for about 10 minutes and one for about 6 minutes. Mircowave was hot to the touch.
I googled "Microwave stopped working", and after reviewing numerous websites with suggestions, I found the response noted below at "Help Owl" which was the most straighfoward and clear explanation to trouble shoot the problem. I first tested the Thermal Cut Out (TCO) per the instructions below and that was the problem. I didn't have to test the electrical fuse. Turns out that you cannot typically use the microwave continuously for more the 12 or 13 minutes or it may overheat and the TCO will shut it down. Extremely easy to test for and fix, and the part is only $15! See Trouble Shooting steps as follows: Make sure that the unit is vented properly and that if you are using it for prolonged periods while cooking, that you turn-on the vent fan.
If there is no display / power within the unit...first check your power source where you plug the unit into the wall.
If that is good, Remove the Cabinette/Cover "Note: it has 3-Torx Anti-Tamper Screws".
Then as you face the microwave from the rear, at the left rear corner is a small circuit board with a fuse. "Check the Fuse"
If the fuse is good, Check the following:
1 - The most common component failure is the "Cabinette TCO" (Thermal Cut-Off Thermostat).
As you face the microwave from the rear...It is located under the cover, on top, on the left front corner area.
It is a Circular, Black & Silver Disc Shaped component about the size of a dime in diameter and is about 1/2" in height.
It has Two (2) Wires attached to it's spade connectors and it acts as a safety fuse.
"IF YOU PUT AN INSULATED JUMPER WIRE ACROSS THE 2 TERMINALS THE POWER SHOULD RETURN AND THE DISPLAY WILL LIGHT"
Anything other than these two items should be checked by an Authorized Service Technician as these microwaves have components thay carry "HIGH VOLTAGE SHOCK HAZZARDS"
If there is no display / power within the unit...first check your power source where you plug the unit into the wall.
If that is good, Remove the Cabinette/Cover "Note: it has 3-Torx Anti-Tamper Screws".
Then as you face the microwave from the rear, at the left rear corner is a small circuit board with a fuse. "Check the Fuse"
If the fuse is good, Check the following:
1 - The most common component failure is the "Cabinette TCO" (Thermal Cut-Off Thermostat).
As you face the microwave from the rear...It is located under the cover, on top, on the left front corner area.
It is a Circular, Black & Silver Disc Shaped component about the size of a dime in diameter and is about 1/2" in height.
It has Two (2) Wires attached to it's spade connectors and it acts as a safety fuse.
"IF YOU PUT AN INSULATED JUMPER WIRE ACROSS THE 2 TERMINALS THE POWER SHOULD RETURN AND THE DISPLAY WILL LIGHT"
Anything other than these two items should be checked by an Authorized Service Technician as these microwaves have components thay carry "HIGH VOLTAGE SHOCK HAZZARDS"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from Coupeville, WA
- Parts Used:
- WB27X10985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Cavity Thermal Cutout Open
Remove cover-the hardest part, as I needed to buy a new set of driver bits that included the dimpled security drivers to remove three screws. GE includes schematic and troubleshooting flow chart with the unit, taped inside the cover. Required more time to look up the part on-line and order it than time used to make the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Lexington Park, MD
- Parts Used:
- WB27X10985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would not turn on
I removed the cover this required a special star Apex tip witha hole in the center. $10 for a set at Lowes.Replaced the fuse and Thermal cut out at the same time. The oven woks like a charm.I would like to add that GE customer service was no help basically told me that it was a throw away unit. If they built it you can fix it.Hope this helps any DIY breathern outthere.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Charlotte, NC
- Parts Used:
- WB49X10097
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Broken plate in microwave
I slipped the new saucer out of the box and placed it in the microwave. I was very disappointed to discover that the new one didn't fly like the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Los Gatos, CA
- Parts Used:
- WB49X10097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke glass plate cooking tray in microwave
New part came -- perfect fit, set it in the microwave, no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Prescott, AZ
- Parts Used:
- WB26X10024
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
turn table motor failed
1. Using wire cutters, cut out sheet metal cover over motor on oven bottom. The stamped bottom is retained by the four corners which were not cut in the stamping. 2. Remove and replace motor. 3. Replace motor cover with supplied screw. (failure symptoms: turn table vibrated before it stopped completely.)
Was this instruction helpful to you?
Thank you for voting!