Models > JVM1660SH03 > Instructions

JVM1660SH03 General Electric Microwave - Instructions

Jump to:

All Instructions for the JVM1660SH03
106 - 120 of 442
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Duane from BUCKEYE, AZ
Parts Used:
WB05X10007
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
One of the 2 door latches broke
Very easy replacement by taking off the plastic trim and than the front portion of the door. Unscrew the 2 screws holding the door handle. Both pieces just snap off from clips. Next pull the spring off the latch and slide the pin that secures the latch to the door. Install everything by reversing your procedures when taking apart completing the repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janet from TREASURE IS, FL
Parts Used:
WB36X10003
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from UNIVERSITY PA, MD
Parts Used:
WB36X10003
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas R. from ETOWAH, NC
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Microwave turntable barely moving and motor making loud noises
Disconnect power to microwave. Remove plastic rotor attached to motor shaft. I had to pry up from underneath it with a screwdriver to break it loose. Cover surface below microwave as bottom cover screws are small and easily lost. Remove three front and two rear screws from bottom cover and it will swing down. Locate the drive motor on the cover, disconnect the power leads, remove one set screw and rotate the old motor off the cover. Reverse instructions to re-install new motor. Swing bottom cover back up and re-install the five small screws. I had a little trouble lining up the screw holes and it helped to use a finishing nail to align the holes in the cover with those in the microwave frame. Reinstall plastic rotor on motor shaft, reconnect power to microwave and test the turntable.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from LAGUNA NIGUEL, CA
Parts Used:
WB36X10068, WB06X10130
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Had a fire in M/W, melting the film and also the spinner cover
Removed old film, installed new horizontally and pulled it downward (match it along the top first). The cover required 2 "hooks" to be removed, only needed 4 clips. Used a screwdriver to remove the 2 clips.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from MEXICO, NY
Parts Used:
WB26X10038
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Turntable would not rotate
Kept the microwave in place( it is above the stove) 1 unplug the microwave 2unscrew the cover plate on the bottom3unplug connections,light and drive motor.4 unscrew drive motor replace with new drive motor,reverse the remaining process. Part took about 3-4 days to deliver,plan accordingly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dik from QUINCY, MA
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Stirrer Motor stopped working
Using a phillips screwdriver, remove 7 screws from the unerpanel of the Spacesaver Microwave. The panel will swing down from the rear edge hinge, exposing the lights and the stirrer motor. Remove the electrical connector and two screws holding the motor in place and remove the motor. The stirrer inside the oven can then be removed if desired. Install the new motor in reverse order. Note rotate the stirrer inside the oven to align the motor shaft to facilitate assembly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terrence from Milton, FL
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Excessive noise while driving the glass tray.
Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
mark from oak lawn, IL
Parts Used:
WB26X10038
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
G.E. microwave turn table was loud and not working
I took it apart and found a small electric motor was not working . I couldn't find it locally so I ordered it from partselect and it was here in just a few days.the repair was easy only a few screws and plug it in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MABEL from GILROY, CA
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Turntable would not turn
took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Raleigh, NC
Parts Used:
WB06X10420
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
turntable motor burnt out
lowered bottom panel, unpluged turntable motor, unscrewed one screw. replaced old motor with new alinged turntable button. repluged motor wire and finished.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Glenn from Tucson, AZ
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
glass cooking tray stopped rotating
I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Highlands Ranch, CO
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Turntable quit working
Took the bottom of microwave off unplugged motor replaced it with new one (two screws) plugged it in replaced bottom and ther you go saved $240.00 over the local appliance repair company. Thanks Mike,
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Maureen from Yorba Linda, CA
Parts Used:
WB06X10224
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Rack holder was catching fire.
Removed the damaged holder by pulling it out. The new one went in with ease. This sure beat the $90 quoted to us to have a GE repair person come to the house. The part was under $7 and under $16 total for shipping. I think we were fortunate to be able to order this part on-line.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BARBARA from PORTSMOUTH, NH
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Turn Table Stopped Working
Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JVM1660SH03
106 - 120 of 442