EMO3000HCC02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bernard from McDonough, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The microwave was making a lot of noise and the glass plate was turning very slowly.
I diagnosed the problem myself. I googled GE parts and was refered to you guys. I ordered the part and it took less than a 5 days to arrive. I used a phillips scewdrive to remove the cover of my microwave and removed the turning glass motor. This took less that 30min and cost less that $50.00. I figured that it would have cost me approx $125.00 to get a tech person to my home for this repair.
Thanks a lot!
Bernard
Thanks a lot!
Bernard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from richmond, IN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
tray drive motor
unsrewed the bottom of the microwave(there was about five or six screws)located the motor unpluged it and unscrewed the two screws holding the motor once installed i reversed the proceedure and put everything back together...simple as 1,2,3...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Orange, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable in microwave stopped working
I turned off the breaker/electric power to the microwave; opened the base of the microwave, detached the wire to the old drive motor, removed the
screws holding the drive motor in place; removed the old drive motor and installed
the new drive motor---beyond easy!!!
Thank you!
screws holding the drive motor in place; removed the old drive motor and installed
the new drive motor---beyond easy!!!
Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Vienna, VA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original drive motor was making noise and not turning the glass cooking tray.
I removed the five screws that held the bottom plate in place. After removing the bottom plate, I unscrewed the one screw holding the drive motor, unplugged the motor, and then installed the new motor. Replaced the botton plate and then tested the new motor. Everything worked like new.
The part was less expensive than buying it from GE. I ordered the motor on a Monday morning and received it Wednesday afternoon. I was completely satisified with the price, part, and shipping time.
Thanks,
The part was less expensive than buying it from GE. I ordered the motor on a Monday morning and received it Wednesday afternoon. I was completely satisified with the price, part, and shipping time.
Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald L from Shafer, MN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
This was so easy. I'm really glad I did not call a repairman!
Removed six screws that allowed the "bottom" to swing down; then removed the two screws holding the motor - disconnected the two wires. Installed the motor and reversed this procedure to finish the project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Vista, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drive tray table failed to turn
unplugged the appliance, removed the glass tray from inside, turned the microwave on its side and removed the 3x3 panel, removed the drive motor by taking out two screws and disconnecting the two electrical wires, compared the new item with the old one, placed new in olds position and screwed in place. replaced the 3x3 cover, turned microwave upright, plugged in the power cord, placed a cup of water on the tray, turned the microwave on for 30 sec. and watched the table turn. Very simple and convenient application.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MANDEVILLE, LA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it broke after 3 days and i was denied a new part or refund
it was easy . i unsrewed 2 srews and it went right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Sparta, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the glass cooking tray would no longer move.
We removed the vents from under the bottom and then the 4 screws and pulled the motor out. It was a no brainer to fix and the part came in alot faster than expected.
Thank You
Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Sneads Ferry, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the plate quit rotating inside oven
removed the srews under the unit unplugged the rotor motor and unscrewed 2 screws holding in the motor. When new motor arrived I plugged it up and put it on with the 2 screws and then put the bottom filter screen piece back on with the 6 little screws. REal, real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Villa Rica, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable wouldnt turn
easy repair. removed seven screws on the underside of the microwave and lowered the bottom cover. removed two screws from the old motor, unpluged the wires. reversed this sequence to install. took less than 5 minutes.
I had previously read these steps others had posted on partselect so the job was a breeze!
I had previously read these steps others had posted on partselect so the job was a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Tucson, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray stopped rotating
I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Highlands Ranch, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable quit working
Took the bottom of microwave off unplugged motor replaced it with new one (two screws) plugged it in replaced bottom and ther you go saved $240.00 over the local appliance repair company. Thanks Mike,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from North Port, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Tray motor stopped working
Removed the cover, 6 screws and then the motor, 2 screws. Unpluged the old motor and just reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Cleburne, TX
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave was making a koud grinding sound
First I unplugged the microwave from the wall receptacle. Next I removed eight screws that let the bottom plate of the microwave hood pivot down with its hinges. Next I removed two screws holding the turn motor in place. I then unplugged the motor and replaced it with the new motor and reversed the above procedures until everything was back in place. I then turned the microwave on and was thrilled to find it working properly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Irvine, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable would not rotate
removed the screws holding the bottom panel, unscrewed the motor. Disconnected the motor. Connected new motor. Screwed in new motor. Replace panel
Was this instruction helpful to you?
Thank you for voting!