SCA2000FB General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Meridian, TX
- Parts Used:
- WB10X10021
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door latch
I held the door open while the repair man took the black facing off and replaced the latch and reinstalled the facing I was worn out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Hillburn, NY
- Parts Used:
- WB10X10021
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Just recently fixed and my son broke it a week later...
My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Southampton, PA
- Parts Used:
- WB10X10021
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Problem door latch
Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Remer from Dothan, AL
- Parts Used:
- WB20X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Could not be turned on
Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Littleton, CO
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Door Interlock Switch Failed
Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Severna Park, MD
- Parts Used:
- 6324W1A001L, WB27X10037
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Timer operated normally, but the microwave did not heat water or cook food.
Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.
Was this instruction helpful to you?
Thank you for voting!