JVM2050SJ04 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from Dublin, OH
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray broke
I laid the new tray in the microwave. There was nothing to really install....but, the woman I spoke to in order to order the tray was terrific and I had the part in two days!! I would recommend this company every time!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Newbern, NC
- Parts Used:
- WB06X10436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
change microwave fan discharge from front to top
damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from gulfport, MS
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
glass broken
replaced the glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Umatilla, FL
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Unit would not come on.
removed access panal, found soft switch as discribed on your web site. removed and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Easton, PA
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace bottom grease filters
Just pull down on "O" ring tab and filter will release. Install new filter in same position. you may have to pull on "O" ring to complete fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Denver, CO
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass cover for Light Bulb was cracked..
It was great...Thank you for having the part available...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marla from Arlington, TX
- Parts Used:
- WB24X829
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan stayed running when door was open...all else working fine
First, unplug microwave. Unscrew two screws at top of microwave, slide grill cover left and remove. This allows access to single screw holding control panel. Remove this screw and lift up control panel to remove. Secondary door switch is black switch at lowest position. The switch is held in place by a lever in back and very hard to get to. Remove the wires plugged into the switch, then remove two screws holding the plastic switch mount that holds all three switches. These screws use a "star" type screwdriver. Once the plastic mount is free, lift it up, right, and tip it slightly to find the lever that will release the black secondary door switch (the lowest switch)...release the broken switch, snap the new switch in its place. Replace the plastic mount by lifting and replacing back into position and replace the two "star" screws. Now, replace the wires onto the new switch, and test operation. Replace control panel, and top grill. It goes faster than it writes...getting the old switch out through that difficult to reach lever was the hardest part...still less than thirty minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Reno, NV
- Parts Used:
- WB27X10735
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The microwave was getting anything hot.
I took current readings between the magnetron and the HVT and saw that there was not current draw. I ordered the magnetron replacement and installed it. We can eat leftovers again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Prashant from Dardenne Prairie, MO
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Microwave would not turn on
Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emanuel from Woodstock, VA
- Parts Used:
- WB06X10436
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Converted an over the range microwave from non vented ductless to outside vent.
Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.
Was this instruction helpful to you?
Thank you for voting!