JVM2070S General Electric Microwave - Instructions

Removed the glass shield and inserted the 2 bulbs. Then replaced the glass shield.

The staff were terrific. Thanks so much as it had a happy ending.

Anita

Replace the fuses

Inside "cavity" bulb was a PITA. Need to remove top decorative trim (2 screws and tabs) to access bulb housing. Broke 1 screw tab so be careful (Wiggle it more). Acccess to bulb housing was made for younger smaller hands, attached by 1 screw. Remove screw, rotate housing, replace bulb. Reverse proceedure. Outside bulb, cake...1 screw, drop lens replace bulb, your done.

unscrew one screw and remove bulb and insert new bulb and replace lense with one screw-

as easy as it gets-

Repair was simple; only a phillips head screw driver was required to remove the access plate.

Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.

remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.

Unscrew (one screw) and take off the cover of the surface light under the microwave (the light over the stove). Firmly pull out the old light bulbs. Align the two prongs of the new bulbs into the socket and firmly push into the recepticle. Replace the cover and screw.

I used the similar screws of my own for temporary until I found parts from PartSelect.com to buy. After I ordered and when it arrives, I just simply replace the missing screws and screwed them in to get LCD TV and LCD TV Stand together firmly without a problem which is much better than the wrong screws I used for temporary.

bought a fuse but that didn't solve the problem. Guess I need a new microwave

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

At first I thought it was just the bulb, but I wasn't able to find a video of the exact model. The dificult part was figuring out how the vent housing came off (turns out it slid to the left then lifted out) but after I figured that out, replacing the cable assembly and the bulb was really easy.

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.

Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.

There are five Philips screws on the bottom outside cover .one at each corner and one at the front center. Remove all four at the corners .leaving the front center for last. When the last screw is removed ,the cover will hinge down, it is attached to clips at the back that allow it fold down. The wire attached to the light socket is connected by a pull apart plug. Grasp at each end of the hard plastic connector and pull outward ,DO NOT PULL ON THE Wires ! Lift the cover from the back of the microwave place it on a flat surface on a towel keep it from sliding around. Remove the screws holding the porcelain sockets. Reverse procedure to reinstall .Installing new Halogen lamps is suggested. Use a clean tissue or cloth to handle the lamps, finger prints on the lamp will shorten the life .

Loosen the two long anchor bolts that screw into the top of the microwave cabinet. These are usually in a shelf or cabinet directly above the microwave. Tilt the microwave forward enough to remove the 2 Phillips head screws from the top of the microwave cabinet. They are near the front. When these two screws are out, remove the fan vent. Once the fan vent is off, remove one screw that holds the control pad in place. Let it hang down. Just to the left of the control pad, you will see wires leading to three switches that close when the door is closed. Use a torx driver to remove the two screws that hold the switch bracket in place. With the bracket out, unplug the wire harnesses. On the opposite side of the wiring connected, a tab holds each switch in place. Lift the tab and slide the switches out. Usually, the bad switch will be identified by a loose or broken spring. Test them by pressing down on the switch. If you notice the bad switch spring, this is usually the bad one. When you have the new one, simply push it back into the appropriate slot and be sure that the holding tab snaps back in place. Plug the wires back in and re-attach the bracket. Put the control pad back on, then the fan vent. When down with those, push on the bottom of the microwave to lift it back into place and tighten the two anchor bolts in the top.