JVM3670S General Electric Microwave - Instructions

I removed a few (6) screws and disengaged the motor. Removed the parts and installed in reverse order. Replaced the screws. Easy

Cleaning up the grease from cooking for years on the stovetop below took WAY longer. But the repair was simple!!

Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube

Odered replacement

removed screw that holds glass for light and replaced bulb.
Reinserted screw that holds glass.

Only down side was cost to ship small bulb.

Found your site online, ordered parts needed. When parts arrived I just put them into the holes in the microwave and popped on the self. Worked like a charm! Thanks very much!

used the Dremel Osciilating tool with small blade to quickly cut/remove the old rack holder and then inserted new hold. Took less then 5 minutes total.

GE microwave displayed the message that Charcoil Filter needs to be changed. I disconnected the unit and removed the top two screws then removed the top panel by sliding it gently to the left. Replaced the filter. And positioned it in the same way the old filter was installed. Replaced the top panel and screws, Connected the unit back and used the Menu option to reset the Charcoil Filter warning option.

Small sized phillips screw driver was required. Once gaining access to the new motor the part(s) replacement was simple.

Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door

There where five screws to remove to get the bottom off then two to release the motor from the housing pull the electrical supply cord out then reverse the process. Piece of cake.

Took out the door to be able to replace the door latch. After removing the plastic cover it was challenging to remove the broken latch (unlike other models this has two separate latches individually controlled by spring. The pin holding the latch was impossible to take out and I figured I need to take out inner layer of the door frame (metal part) to remove it. But the frame was stuck and did not come out. I found no reference how to do it on internet and then with another pair of hand pulled outwards while simultaneously pulling upward. Was finally about to pull just enough and replace the latch and push the metal frame to fit back.

I ordered and replaced the coupler. Once installed, all was well!

It was very easy to remove the old charcoal filter and insert the new charcoal filter(had done it before with with the replacement filter GE had included with the purchase).

Remove two screws on the top of the grill. Slide the grill to the left and then pull straight off. Slide the filter in place. Replace grill and screws

Removed the light cover screw with a Phillips screwdriver. Removed the lamps from the packaging just enough to free up the 2 prongs for fitting in the socket. Make sure the power is in the "off position". Install the bulbs one at a time by lining up the 2 sockets (Very important not to touch the halogen bulb glass surface while installing them). Energize the light switch to check operation of the new bulbs.