GLMV169DBA Frigidaire Microwave - Instructions

The door was an easy off easy on type, we slipped the old door off quickly. It was a bit tricky getting the new on for some reason . It took a few tries.

WE were most impressed with the speed and accuracy in getting the parts from Parts Select I got the correct replacement door the very next day, and we did not request any expedited handling.

Separated the two elements on the front door. Then inserted the new handle and reconnected the front door. It was an easy installation.

I bought the door assembly online while in Afghanistan. My wife who has no mechanical ability installed the door in less than 15 min. She used a flathead screwdriver to gently pry open the hinges (they returned to their original position afterward) by applying pressure on the bottom hinge and removed the old door. Repeat to put the new one on. Most of the time was figuring out how to get the old door off.

Open the microwave door.
On the interior of the door, there is a plastic molding around the locks and most outer part of the door. Pop that with a flathead screwdriver or butter knife. You’ll immediately see two screw heads. Screw counterclockwise to release the fragments of the old handle. DO NOT THROW THOSE SCREWS AWAY. Reattach new handle using the same screws. Pop the piece of plastic molding back in and you’re done.

It was simple, just used a flathead screwdriver for a little leverage at the top hinge and it slid right on.

I gently lifted with a screwdriver the inside plastic encasing on the side of the hinges, without removing the encasing completely. Had to do this to be able to lift door up and onto the upper hinge. Placed the door into position by gently moving it towards the wide-open position.
(Felt proud of myself because there were no instructions included in the box with the replacement door.)

Used plastic putty knife to separate inside door plastic molding from metal door frame. Small section at a time starting from latch area. Worked the knife around door to separate plastic molding. Leave plastic intact near door hinges. Carefully separate out of the way the molding, and access Phillip screws with long screw driver. Replace handle and screw tight the screws. Push into place the plastic molding with your fingers until it clips back into place. The end.

My model had a cover on the interior trim around the glass that when removed allowed the door to lift off. The new one did not.

I removed the interior trim and swapped them. You can probably remove the trim to remove or install the new door. Reinstall the trim when the door is on.

I took off the keypad panel,then plugged it back in,turned it on for 2 seconds so I can see where the spark was comming from,saw it was the capacitor, unpluged it while it was on so the voltage would drain,took out the capacitor ordered it a few days later,put it back in, now the wife is happy,and when she is happy,I'm happy :-)

This is an OTR microwave oven, needs to be removed to diagnose problem. I did not diagnose problem properly, I searched online for possible causes, read that (99%)percent of the time the interlock switch was bad and replacement should solve my problem. It was also stated to be an easy fix,15- 45 minutes depending on ability. I ordered the relay switch. Took the oven down then removed outer shell. With my multimeter I began to test, fuses(2), interlock switches(3)and transformer. 3 interlock switches were ok, fuses were fine, and had power to the transformer, meter could not read output of transformer because of high voltage, (2300v). I'm down to magnetron (about a hundred bucks) or the touch pad/ circuit board. I have a countertop micro that I'm putting in place of the OTR. As far as Partselect, my item was shipped and delivered on time, instructions for changing that part was quite accurate. Would order from here again, just do my homework first.

First called for a repairman. They didn't work on any thing over ten years old because "parts are not available". They would look at it for $86.00 service call. I found a video on You Tube that gave a good description of the problem and how to repair.
I first looked in the oven and found no bare metal that would cause the problem. I then removed the Stirrer cover and stirrer in top of oven where I discovered that the stirrer had been arcing to the cabinet. Easy fix. I sanded down the damaged area to clean metal then repainted with microwave paint. I installed new stirrer Part Number PS2343147 and replaced Stirrer Fan Cover. Microwave works like new.

easy..just slipped it in the space part camesightlybent, but was okay..

Pried off the inner molding around the door to access screws. Attached new handle. reattached molding. Very easy

I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.

Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.