CFMV156FMA Frigidaire Microwave - Instructions

I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.

Removed the retaining clip that keeps the door on, took the door off. Removed the plastic rim that is clipped into place. Removed old screws holding on handle and replaced.

Part arrived in one day. Old part snapped right out and new snapped right in. One minute repair with no more sparking and no need to invest in a new microwave... which is what I thought I was going to have to do.

Removed the 3 screws to drop the lower panel and, removeed the turn table plate and ring. Then removed the 2 screws holding the motor, the 2 wires attached to the motor and removed the old motor.Replaced the new motor in the reverse order. DO NOT FORGET TO UNPLUG THE MICROWAVE FIRST.

was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a 12 volt battery and it was bad. Ordered a new one from Part select and got it fast . Works great .

After unplugging the unit remove the control face buy removing the screws. All three door switchs are on a bracket on the left. Remove the two screws holding the bracket in place and pull out. Disconnect the wires from the three switches and test each switch indivually to determine the bad one. I used a multimeter set on ohms.Replace the bad switch with the new one and replace all the wires. Reassemble the unit and you are good to go.

Open the door and start at the outside perrimeter of the plastic moulding by inserting the putty knife and gently prying up.I started at the 2 latches that secure the door when it closes.Work your way around to the top and bottom. I was able to leave the portion of the plastic moulding by the door hinges still intact while removing the screws for the handle and replacing with the new one.After handle is on gently snap moulding back in place.Remember start at the inside of the door in the small opening at the outter edge of the door.

It is a undercabinet stovetop microwave. First had to take it down and unplug. Remove the top cover locate the door switch. Used neednose pliers to remove switch. Unplug two terminals.Plug new switch and use pliers to replace back @ same position.Plug in socket temporarily to see if it works.Afterwards if it works.Unplug and replace cover.Ready to be replaced back under cabinet.

The mv was originally installed as recirc venting as there was no outside vent. I hated the steam and smoke just being put back into the kitchen.

I removed mv unit, ran a vent thru cabinets, thru attic, to outside vent. Installed new part on top on mv, installed mv and hooked up to new vent.

Works great now. Getting a good tight seal was difficult because the area the vent ran was so small.

Replaced Filters very easy to do

It was really simple. I used the putty knife the seperate the plastic trim, paying particular to start near the latches as someone else posted. Once the trim was pulled back Wow the screws were right there. I unscrewed the broken handle and attached the new handle. It was really easy and my wife thinks I'm amazing thanks for the help.

With the amount of force needed to open the microwave door I can see this repair repeated. Some of the handle was still attached to the door so I could open it easy enough. there is a flamge covering the scerws to remove the handle. using a small flat blade screw driver aids in the removal of the flange to expose the screws. the square flange surrounds the entire frame of the door.remove the screws located in the recessed edge along the outside edge of the door.do this by viewing the location of the peices still attached to the door. after removing the screws and broken parts of the old handle,place the new handle in the cutouts where the handle is located,replace the screw,this may take some force since the handle is new. reposition the flange to the framevia the snaps along the edges and becareful not to force it because damage to the snaps are possible.thats it,two minute repair.

Removed the inside door cover by taking a putty knife and inserting it by the door levers all around the door while pulling forward to seperate the cover so the screws that held the handle on could be reached. However, the part did not fit and had to be returned. Replaced cover by pinching it back in place.

easy putting together. 15 mins to repair. the old grille was taken away by a technician and he took the part and disposed of it for me, i didnt know he took screws also. So when i got the new part i thought it would have new screws with it - and it didnt - no biggie...so i had to go purchase screws for the holes in the grille.

Used putty knife to unsnap tabs to separate inner trim on top, bottom and handle sides (left the hinge side attached), removed upper and lower screws, replaced handle, reinserted screws (tight fit, big fingers, several dropped screws, one under the stove = 15+ minutes), re-snapped trim