GLMV169DBF Frigidaire Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Todd from Parker, CO
- Parts Used:
- 5304440323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave Door Handle Busted Off (At Top Of Handle)
Easy as 1-2-3! Removed door from unit (top right hinge has an easy small lock that simply "snaps out" with a standard screwdriver. Placed door face down on table. Removed outer (perimeter) frame with standard screw driver, by plying up. Removed the two screws (to the handle) from the backside of door with a phillips screwdriver. Replaced with the new door handle and repeated the above steps in reverse. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Greer, SC
- Parts Used:
- 5304441374
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Handle Broken
Took longer than it should due to no instructions being in box. The removal of the old door took approx 30 secs and was self explanatory. Once I realized I had to remove the plastic inner panel on the new door to re-install it, it also took only minutes. Could have been an easy fix with instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Framingham, MA
- Parts Used:
- 5304440335
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
annual replacement of filter
My husband did it by just taking off the panel on the top of the microwave and replace old with new. We cleaned up some of the accumulated grease as well on the microwave. He had a little problem with the screws. We have done this before so no big problem. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Brighton, MI
- Parts Used:
- 5304441374
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave door handle broken
After trying to bend parts that do not bend I realized you need to remove the plastic gasket around perimeter of microwave door but leave it loosely hanging on (pry off with screwdriver) With the gasket removed you can fit the door on and the snap the gasket back in place before closing and testing. The door was a perfect fit, it works great. The door will not go on until you remove or bend back that gasket. It's not obvious how or where to remove but just put a screwdriver in there and you'll feel it pop out and it snaps right back in after assembly..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chase from Tampa, FL
- Parts Used:
- 5304440323
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken handle
I found and removed the clip for the door - top on the inside (not easy to find) and then removed the door. Called support who told me to watch you-tube and there were good instructions there. Needed needle nose pliers to hold broken screw and a screw driver that could fit between the metal. Flat head and phillips are required. OH you should try to leave the screw in the hole as getting it back there is a PIA. Took about 20 minutes and I am challenged mechanically. Altogether, not too bad.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Carlyle, IL
- Parts Used:
- 5304441374
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door broken
The new door is slightly different than the one I replaced. To install the new door, I had to remove the plastic "frame" on the new door with a small flat head screwdriver. Then, I could easily mount the door to the hinges on the microwave. Once on the microwave, I clicked the frame back into the door and it was good as new!
Was this instruction helpful to you?
Thank you for voting!