MWR365 Caloric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terri from Kingsland, TX
- Parts Used:
- WPA3167501
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bulb
Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathtleen from Bristol, CT
- Parts Used:
- WPA3167501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out lightbulb for over 20 years
Unscrewed back plate, and replaced bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Biao from Houston, TX
- Parts Used:
- D8547912
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Maytag Microwave UMC5100AD fixes
My Maytag Microwave UMC5100AD was suddenly broken in 1 second when I heated food last time. Then no clock, etc, seem the fuse broken. to fix it, the most difficult part was how to remove it from the wall trim. Finally got it out. Then went HomeDepot to get the same fuse, replaced and used it, burned again. Then I searched online and ppl said the capacitor might be the one. I took it out and measured it, yeah it indeed was a problem since it's not open. Then I order the capacitor from PartSelect about $32. After 3 days I got it and installed it. Done. Sure need to put the Microwave back to wall trim. That's it. Saved about $500 buck if I buy a new one plus labor to install it. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BURSON, CA
- Parts Used:
- WPA3167501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light bulb went out in mictowave
Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuong from plano, TX
- Parts Used:
- D8547912
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
Fuse blows when start cooking.
Replace the capacitor and the fuse. Then it works again. Part arrived in an open plastic bag with scratch. It looked like a returned part, but it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Marietta, GA
- Parts Used:
- B8371001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic clip caused the rack to arc to the side of the cavity.
Pulled out the old clip and pushed in the new one. Only tool was my fingers and took about 20 seconds. This was after the Sear's web page said the part was no longer available and no replacement was listed.
Thanks to partselect.com I saved the microwave for another couple years.
Thanks to partselect.com I saved the microwave for another couple years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deidre from Brownsville, TX
- Parts Used:
- WPA3167501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave oven bulb had burned out
My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
The whole operation took less than 5 mins.
Thank you.
The whole operation took less than 5 mins.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!