RO-10AP74067-1M Amana Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terri from Kingsland, TX
- Parts Used:
- WPA3167501
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bulb
Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathtleen from Bristol, CT
- Parts Used:
- WPA3167501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out lightbulb for over 20 years
Unscrewed back plate, and replaced bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Roseville, CA
- Parts Used:
- R0156726
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass tray
There was nothing to actually, I just put in the bottom of the oven and cooked my sausage about 40 seconds later there is a loud POP and that's it. End of repair, end of breakfast, end of oven. I am returning the glass tray to you and asking for a refund. It was less expensive to go buy a new oven then to have that 30 year old repaired!
I do thank you for you prompt service and shipping.
We can't say we didn't try.
I do thank you for you prompt service and shipping.
We can't say we didn't try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from HATTIESBURG, MS
- Parts Used:
- 285222
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
It was the heat safety switch in the old drive motor
It was fairly easy a few tight spaces to reach in but all in all it was pretty straight forward
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BURSON, CA
- Parts Used:
- WPA3167501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light bulb went out in mictowave
Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deidre from Brownsville, TX
- Parts Used:
- WPA3167501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave oven bulb had burned out
My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
The whole operation took less than 5 mins.
Thank you.
The whole operation took less than 5 mins.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Jacksonville, FL
- Parts Used:
- WP10794402
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Magnetron shorted out blowed 15 amp fuse
removed cover of microwave, replaced fuse checked for short at plug with volt ohm meter, there was a short at the plug then checked magnetron for short and there was a short at the magnetron, the cap and diode checked good.
replaced magnetron IT IS WORKING GREAT !!
replaced magnetron IT IS WORKING GREAT !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Millis, MA
- Parts Used:
- 285222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
Washer Had A Continuous Moan And Vibration
I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred the bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.
Was this instruction helpful to you?
Thank you for voting!