ACO1860AB-PACO1860AB0 Amana Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Norman from Rehoboth Beach, DE
- Parts Used:
- R0130588
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
origianl door had a hole in it
replaced door frame assy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from CHICAGO, IL
- Parts Used:
- WPA3073101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light over range burned out
Philips screwdriver
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.
Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/delivery was fast. No need to have spare on hand.
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.
Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/delivery was fast. No need to have spare on hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from PITTSFORD, NY
- Parts Used:
- WPA3073101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
No problem
I had a son put in the new light bulbs. Rather simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from CAMPBELLSPORT, WI
- Parts Used:
- WPR0130614
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light covers yellow and cracked
Removed screws. replaced bulbs with led bulbs install new covers replace screws led bulbs no heat wont crack covers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from EVERETT, WA
- Parts Used:
- WPR0130614
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The part as supplied is a generic for several models. The clip end is bigger than the slot and will not fit as shipped.
The clip end is @ 1"; the slot is @ 1/2". There are two raised pieces on the clip each @ 1/4" in. I used a metal snip to cut the oter 1/4" off each end-this allows the clip to be inserted into the slot and hold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from WALLAND, TN
- Parts Used:
- WPR0130614
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
New covers did not fit. The flange on the new covers had a flange that was too big for hole.
Sawed off edges of covers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Swansea, MA
- Parts Used:
- WPR9800384
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
One of the shelf plastic holder was broken
I was able to find the part on line and within a few days received the part and installed it with no problems thanks to the website drawing information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael J from LORAIN, OH
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb which lit the surface of the range.
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roland R from NORTH ANDOVER, MA
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lightbulb burned out
Removed one screw lowered glass cover removed burned out bulb replaced with new one put glass back reinstalled screw. Dune 5 minutes back in business
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfred from summerville, SC
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt Out Light Bulb Replacement
Open compartment, installed bulb, closed compartment
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gwynn from Calvert City, KY
- Parts Used:
- WPR9800384, WPR0131462, WPR0130608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Microwave was sparking & fire going up the side
After reading on-line about other Amana microwaves, that said the arching was probablly due to dirt or grease & I knew it wasn't dirty, I decided to try the sandpaper recommended to clean the carbon from the wall where the shelf holder had burned several years ago. This caused the remainder of the clip to become loose. I then took a sharp knife & popped the clip out which left a neat square hole which your shelf holder popped right into. The filters were an afterthought because I didn't want to pay shipping for only a $2 item
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from STOCKTON, CA
- Parts Used:
- W10207572
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn table stopped working.
The turn table motor stopped turning ,but we never turned the off button off on the microwave and kept using it ,so it shorted to the outlet neutral (white) wire at the circuit breaker fuse panel , the wire burnt off. I cut the wire re-installed it in a good buss connector.That restored power back to the outlet.** So now to replace bad Turn-Motor: Using phillip screw driver remove (bottom)filter/light panel- 10 screws, unplug lights and motor connectors, lower panel out of the way ,remove 2 screws from motor and replace motor. Install in reverse order. (Fast Fix)**Note:If you had other problems like I did consult with a professional electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Mesquite, TX
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb burned out
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Gatlinburg, TN
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb
Replaced light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roger from palm coast, FL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace light blub
removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.
Was this instruction helpful to you?
Thank you for voting!