AMV1150VAW4 Amana Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from WEST NYACK, NY
- Parts Used:
- WPW10466420, W10337248
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable Motor burned out
Unplug microwave
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet
r
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet
r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from LAS VEGAS, NV
- Parts Used:
- W10337248
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sparks from drive coupling
remove 6 lower screws, removed lower panel,2 screws holding drive motor,lower motor, remove old coupling from inside microwave and replace with new coupling, re install motor,install lower panel and screws.no more sparks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Locust Grove, VA
- Parts Used:
- W10259625
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken plastic tabs on vent cover grill.
Insert new grill, tighten 2 screws,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from MAYS LANDING, NJ
- Parts Used:
- W11025649
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
needed microwave mounting bracket
mounted bracket, case closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from MOUNT ULLA, NC
- Parts Used:
- W10269458
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The close door warning kept coming on and the microwave would not run
Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from MIDDLEFIELD, CT
- Parts Used:
- W10727360
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Failing Door Switch. Preventing unit from operating.
Removal of Phillip Head screws from Top vent and Control panel. Removed Torx head screw to remove entire switch assembly. Removed three wires to switch leads. Unclipped old switch. Replaced wires and inserted New switch in to clips. Attached assembly with Torx screw. Set Control panel back into place and screwed in top screw. Replaced upper vent with 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kat from Hudson, NC
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights bulbs burned out
Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from CARPENTERSVLE, IL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
light bulb burnt out .
Turn off power supply at breaker . Replace old bulb with new bulb .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Marietta, SC
- Parts Used:
- W10259625
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screw broke out.
Put into place, tightened the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Cincinnati, OH
- Parts Used:
- W11252182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turntable broke in half, ring turn needed replaced
I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next
Service was fantastic, parts were ordered one day and received the next
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pablo from Burlingame, CA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb burned-out
screwed in new bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hudson, MI
- Parts Used:
- WPW10156813, WP8206419
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Top support for door switch broke.
Part of the support was missing. I had to remove the two switches and put them in the new bracket
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MERIDIAN, ID
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Range light bulbs were burned out
We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from OVERLAND PARK, KS
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out bulb
Husband replaced the bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon C from MEDFORD, OR
- Parts Used:
- W11252182
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Microwave didn't have support ring when house was purchased.
Removed turntable
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Was this instruction helpful to you?
Thank you for voting!