AMV5206BAW Amana Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- scott from milwaukee, WI
- Parts Used:
- DE67-00213A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Table Will Not Spin
Try to turn Coupler. If it is loose it is broken 1. pull old one out 2. line up keyway on new one and press it in. (If mild resistance was felt while turning coupler it is not coupler most likely drive motor)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tipton, MI
- Parts Used:
- WPDE31-10172A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
motor was slipping
replaced the drive motor and coupler coupler from samsung parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tasha from York, PA
- Parts Used:
- 4713-001165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light under the microwave went out
To replace the light bulb was fast and easy. All I had to do was unscrew one screw and place the bulb in! Quick and easy, and simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Clovis, CA
- Parts Used:
- DE67-00213A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
tray would not rotate
Snapped the coupler in place. Took one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Seattle, WA
- Parts Used:
- DE67-00213A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The turntable on the Microwave stopped turning
Asked at Best Buy what our options were after I described the problem. They said to buy a new Microwave. I thought No way it is only a few years old. Whent home did som research and found your site and for under $5.00 My microwave turn table turns again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- al from lexington, SC
- Parts Used:
- DE67-00213A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tray inside would not rotate
Removed old coupler with my fingers and installed new one on shaft. Works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Phoenix, AZ
- Parts Used:
- 6802A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave Vent Hood Filters
Not so sure this would qualify as "instructions", but I only needed a screwdriver because the "D" rings of the old vent filters broke off and I had to pry to old ones out. Keep in mind, I am mechanically disadvantaged and can barely change an A/C filter ... that being said, all I did for this order was input my Model number and PartSelect found the correct replacement part. I receive the parts super quick (faster than the other 2 purchases I did that day). The only bummer was the packaging ... super huge box for small tiny parts. Otherwise, I now know where to go for replacement parts. This project should be a "no-brainer" for most DYI's, so getting the right parts with just a model number was lifesaving for me :0)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Pedricktown, NJ
- Parts Used:
- DE47-20059B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no power
took THERMOSTAT;NT-101NA,250 out and put THERMOSTAT;NT-101NA,250 in so easy got the part in LESS 19 HRS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juel from White Bear Lake, MN
- Parts Used:
- 4713-001165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bulb burned out
Replaced the bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Paso Robles, CA
- Parts Used:
- WPW10126786
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
microwave acts like its working but won't heat.
Replaced the magnetron and diode. Microwave works prefect now.
Was this instruction helpful to you?
Thank you for voting!