YJMV9196CB1 Whirlpool Microwave Oven Combo - Instructions

Unplug the microwave. Removed the glass tray, the roller ring, and plastic piece that sits on the motor shaft from the inside of the microwave. Remove the 12 Phillips head screws from the bottom of microwave, let the bottom hang down on the mounting hooks at the rear of the microwave. Remove the 2 torx screws from the mounting bracket under the microwave lower the turntable motor remove the two leads. Transfer the rubber washer from the old motor to the new and reassemble and test. It took longer to write these instructions than it did to do the job.

Hint: if the microwave is over a stove lay a towel across the stove to catch any screws that may fall.

Good luck and enjoy your fully functional microwave!

I first unplugged the microwave. I then unscrewed the 2 screws from the top grill. I had to be careful because the grill was cracked close to each screw. It was a little tricky to remove the grill. Had to tilt it down as I removed it, and make sure the microwave door was opened as wide as possible. Filters were placed as the old ones, with the metal part up I believe. A little tricky to get one of the filters to fit. Grill was replaced with care so as not to further Crack it. Kind of maneuvered grill back in place, getting right side in place first. I noticed there were several tabs on the grill that needed to be placed inside of the microwave body while reinstalling the grill. Once the grill was in place, the 2 screws were put in to hold the grill in place.

remove 6 lower screws, removed lower panel,2 screws holding drive motor,lower motor, remove old coupling from inside microwave and replace with new coupling, re install motor,install lower panel and screws.no more sparks

Replaced bulbs easily.

Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.

Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.

mounted bracket, case closed.

Part of the support was missing. I had to remove the two switches and put them in the new bracket
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.

I had the help of a handyman, I'm 75 years young but not handy with tools

Just opened the door and dropped in new part and viola!

Used a philips head screwdriver to remove one screw holding the light cover. Pulled out the old bulb and inserted the new one. Replaced the cover.

Unscrew lens and direct access to surface light cavity. Removed old light bulbs and replaced with new bulbs. Reassembled lens cover and turned lights on successfully. Took less than ten minutes.

took it out of box wooolaaa fixed thanks fast shipping too...

It was a very simple and easy fix, no tools needed. First, open the door to the microwave/oven and remove the glass plate and the plastic plate guide. Next, locate the whole in the center. Using your finger, find the drive coupling pin that sits just below the opening (half circle shape). Align the bottom of the drive coupling with the metal pin and press down. Replace the plate guide and plate. The grooves in the bottom of the glass plate should be aligned with the shape of the drive coupling. Test by setting microwave/oven to 30 seconds and watch for proper turning and alignment.

Removed the old turntable tray, replaced it with the new one.