RM975PXLW1 Whirlpool Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Johnson from Norwood, CO
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element Failed
I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Spooner, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element went bad, will not work.
As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fort Collins, CO
- Parts Used:
- WP8189867
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
light wont come on
Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from SEBASTIAN, FL
- Parts Used:
- WP688805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The dryer nob wasn't working the dryer knob broke off inside the unit
It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him
Was this instruction helpful to you?
Thank you for voting!
Heat in elements was inconsistent
Removed block (1 screw) Cut 2 connecting wires. Strip insulation. Attach new block with wire nut(per enclosed instructions) Heat shrink wrap with Lighter. attach block. 10 minutes: problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carolyn from ROGERSVILLE, TN
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element was broken
was very easy to install I only needed a phillips screwdriver to remove old part and install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MIDDLE RIVER, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Longview, TX
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element broke into several pieces
Was able to use a philips screwdriver and remove 2 screws. I then clean the bottom of the oven. The installation was even easier. Took less than 5 minutes. Saved over $60.00 in labor cost
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- denise from swartz creek, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element quit working
Removed the 2 screws that hold the element in place. Pulled the element forward about 3 inches and disconnected the two wires. Plugged the wire clips onto the new element and pushed the element back into place. Put the 2 screws back into place. This was a very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lowell from Aberdeen, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn on the oven to heat up for cooking, Heard a ark sound, open the oven door and there was a fire on the element. Turn off the oven.
I had to pull the stove out from the wall and discounted the power source from the wall. Than I used the a phillips screwdriver take out the heat element. There was now problem fixing the stove. Lowell Moxley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from burnthills, NY
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out bake element
unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Lawrenceville, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The original bake element cracked, causing sparks and a small, brief fire on the crack. Next, the element would not heat.
First I turned off the circuit breaker to the oven. Then, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches to disconnect the two wires. The connectors were tight, so required a little wiggling to disconnect the wires.
Upon receipt of the replacement element, I turned off the circuit breaker to the oven. Then, I reconnected the element wires, pushed the connect wires into the back of the oven, and rescrewed the unit in place. With the circuit breaker turned back on, I tested the oven. It worked great. Very easy!
Upon receipt of the replacement element, I turned off the circuit breaker to the oven. Then, I reconnected the element wires, pushed the connect wires into the back of the oven, and rescrewed the unit in place. With the circuit breaker turned back on, I tested the oven. It worked great. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEPHEN from SEMORA, NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom element of the oven stopped working, therefore, we could not bake anything.
First, I turned the breaker off to the oven, that's the most important step.
Next, I turned on the oven to make sure the oven was not energized.
I then took out two phillips screws that were holding the baking element in place.
Next I pulled the element out slowly to expose the wires that connected to the element.
I removed the connecters, took out the damaged element, replaced it with the new element.
Last, I screwed the two phillips screws back in, and saved a $65.00 service call.
Next, I turned on the oven to make sure the oven was not energized.
I then took out two phillips screws that were holding the baking element in place.
Next I pulled the element out slowly to expose the wires that connected to the element.
I removed the connecters, took out the damaged element, replaced it with the new element.
Last, I screwed the two phillips screws back in, and saved a $65.00 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patsy from Coppell, TX
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The bake element burned out and the oven wouldn't heat.
First, my son pulled the range out and I unplugged it. Then he removed the 2 screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the wires. Then he placed the new element in the oven, connected the wires and put in the screws back in. It worked immediately!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Chesterfield, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
old heating element "popped"
Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!
Was this instruction helpful to you?
Thank you for voting!