RM288PXS0 Whirlpool Microwave Oven Combo - Instructions

Now I know why everyone said "less than 15 mins" for installation time...because "less than 5 min" wasn't an option! Went exactly as everyone described, just more quickly - turned off breaker, removed two screws, disconnected wires, reconnected wires to new element, re-attached it with screws, turned on breaker, checked it - worked like a charm. It was more work opening the box! Would have taken less time if my flashlight hadn't rolled off the open oven door leaving me with poor lighting conditions.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
then I reconnected the two wires to the new element and put back the two screws that hold the element in place and the job was finished.

First I checked to make sure the power was off with an electrical meter (wiggins). Next I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then pulled off the 2 wires replaced the element and put the 2 wires on the new element. I screwed it back into place and tested the element. When I turned the oven on my new element began to glow red and the repair was now complete. Super easy.

First I unpluged the stove, then I removed the two screws that hold the heat element in place. Then I pulled the heat element out a couple of inches and disconnected the two wires.
I just plugged in the new element wires, pushed the element in place and replaced the screws.
It only took about 10 minutes at the most.

Turn off the power, removed the two screw (needed a wrench to help turn screw driver at first). Pulled the element forward to expose the wire connectors. Removed connectors from the old element. iInstalled new element to the wire connectors (slide on), screwed plate back into oven. Turn on power and tested

Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of burner wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed

removed the two screws that hold the element in place, then slowly pulled the element out and disconnected the two wires, then reconnected the wires and screwed it back in - I'm a 25 year old female and did this in less than 5 min. - don't wait any longer to fix your oven!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then reverse the process and bingo ...done

EXTREMELY fast shipping of product ...I have purchased other products and always satisfied .

Super simple, and the part arrived less than 48 hours after buying it online. I turned off the breaker to the oven and unscrewed the burner at the bracket holding it to the back wall of the oven. After pulling out the wires, all you do is tug at the two connectors and they detach. Just slide the new burner's connectors in, then screw it back into place. My arms aren't quiet long enough to reach all the way back there, so I got my son to help and I held the flashlight for him. Had it done before my husband got home from work!

my wife took the old element out i used a screw driver to remove it...i then ordered the new part using this web site...i then let my wife install the new element she then attatched the wires she used her fingers to tighten the bolt....and she is very very impressed with herself.

Turned off circuit breaker for oven. Unscrewed the 2 screws that held the element in place on the back wall of the oven. Save those screws! Pulled the element out from the wall. Disconnected the 2 wires. Attached the wires for the new element and then screwed the new element into the back wall. Flipped the circuit back on and the oven was fixed.

Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.

Just pushed in a new clip which was very easy.
Excellent service. Only took 3 days from Calf.

First, turn the breaker off to the oven, you don't want to electrocute yourself. There are two screws that hold the element to the back wall of the oven, undo those and pull the element towards you. There are two terminals at each end of the element, take these off, then reattach to the new element and screw back in to the back wall of the oven. This process takes maybe all of five minutes

turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.