RM288PXS9 Whirlpool Microwave Oven Combo - Instructions

Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.

Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of burner wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

I'll tell you.......PartSelect said the items would take from 3-5 days.....I got them in 48 hrs. I turned the breaker to the oven off. I unscrewd two screws from the back of the oven and pulled the element out and took it off of two connectors. Repeated the same with the broiler element. Job done saved $200.00...Job was quoted at $259.00

We have had our Whirlpool oven for 22 years and became very concerned that a part would not be available. We were thrilled to find the part as well as install the new part ourselves. With a screw driver, we disconnected the old baking element ( be sure to shut the power while doing this) and screwed in the new one. That simple!!!

The hardest part was figuring which breaker controlled the oven because it wasn't marked in my breaker box (it IS now!). So, first I killed all power to the stove, then unscrewed the 2 screws in the back of the oven holding the element. Pulled the element forward, then dissconnected the 2 clampy connector wires (yes, I'm a girl, no correct electrical jargon here). These were a little difficult because my oven is 21 years old & this is the first replacement I've had to do. I reconnected the new element clamps(which was easier), pushed the wires back through the opening & reinserted the screws. Threw the breaker back on, turned on oven to 200 degrees & let heat until the set temperature light turned off as a test. Voila - oven fixed!

I order the part on 7/29 and much to my surprise, it arrived the very next day. It took less than 15 minutes to remove the old element and installed the new one. It was a little difficult to unplug the old one and took quite a bit of pulling but it came out okay. Plugging in the new one and screwing on the cover plate was easy.

turned power off Unscrewed 2 screws pulled old element out slightly . disconected wires . connected wires to new element tightened 2 screws turned power back on baked a pie. took longer to type this

i received the part via fed-x i opened the box uninstalled the old part installed the new part turned it on the element got red hot and it works just fine.

Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.

1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!

Pulled old one out, installed new one with a twist of the screw driver. Easy!!!

I removed the two screws for the bake element, diconnected the two wires attached to the bake element. I then reattached the wires to the new bake element, secured it with the two screws and I was done. It took five minutes and the oven works like new.

Used screwdriver to unfasten the old element from the oven frame. Then unplugged the two wire plugs from the back of the old element. Reversed the process to install the new. Couldn't have been any simpler.