RM288PXS9 Whirlpool Microwave Oven Combo - Instructions

As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!

was very easy to install I only needed a phillips screwdriver to remove old part and install new one.

This microwave is the upper unit in combination with an oven. Microwave portion is Model RM288PXS. Cut power at breaker box. Remove metal frame around 2 sides and top, (5 screws). Remove 4 screws on bottom, whicn anchors the unit to the frame.Remove contol panel (2 screws at top) and swing down. Pull out female electrical socket at bottom right back in conrol unit space. Now pull out microwave from frame about 6-8 inches. This provides access to pulleys on the motor and wave disperser. Put on belt. Reverse the above procedure to finalize the repair. This is the 3rd time I have had to replace this belt. They last about 6-7 years. Without the wave disperser , the microwave does not provide even heat.

The new handle, braces and screws arrived as quoted. My son-in-law installed the new one without much trouble. The handle is black and matches the black front of my stove. The older handle was sort of a wood-brown. Thus I like the new one better. Thank you for good service and prompt attention to the problem.
Linda Archibald
Hanson, MA

Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)

Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!

First, my son pulled the range out and I unplugged it. Then he removed the 2 screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the wires. Then he placed the new element in the oven, connected the wires and put in the screws back in. It worked immediately!!

Was waiting on my friend's boyfriend who is a contractor to switch this knob out but figured it out myself. It just slides on and off with no tools. I am so proud of myself for completing the repair all by myself on my 37 year old oven. My other knob just cracked and I was afraid the inside of the knob was damaged but it is not. Working like a charm now.

The new knobs slide on and fit perfectly. No tools or labor required.

Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.

I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.

Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!

I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!

removed two screws installed new one replaced the screws. The service I received couldn't have been better. They did exactly what they said they would. I wouldn't hesitate to use them again or recommend them.

First I turned off the circuit breaker to the oven. Then, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches to disconnect the two wires. The connectors were tight, so required a little wiggling to disconnect the wires.

Upon receipt of the replacement element, I turned off the circuit breaker to the oven. Then, I reconnected the element wires, pushed the connect wires into the back of the oven, and rescrewed the unit in place. With the circuit breaker turned back on, I tested the oven. It worked great. Very easy!