RMC275PVB01 Whirlpool Microwave Oven Combo - Instructions

I turn off the power in the breaker box and then unscrew the part and replace it with the new one

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

I took the new tray out of the box and placed it in the microwave oven.. No tools needed.

Replaced the glass tray

no repair needed - ordered part, came within 3 days - very satisfied

Easily replaced after received the product from Part Select. Very satisfied.

found the part no. and ordered it. it was delivered fast and efficient.
tracking was also helpful.
thanks

I follow the directions on the Maytag site. It is a very simple job. I appreciate the Information I got from Becky when ordering the hinges.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

We had to remove screws from the vent covers above and below the microwave, then there were 2 screws (one on each side) that attached the microwave to the oven. Once all of the screws were removed we had to pull the microwave out. Then we pulled the light cord out, removed the burnt out light and installed the new one. Then reversed the steps.

We followed the instructions given by Parts Service. The only problem we had (Whirlpool left two screws out of spacer bracket and it fell out requiring further removable of inner glass to replace spacer. Process took about twenty minutes.

Well the repair went Ok. The probelm happen on the following Monday. You see I ordered this part over the phone because I had to make sure it would arrive in time for Thanksgiving.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.

I am not a big do-it-yourselfer, so maybe I might have found this more difficult than expected. When I first looked at the oven before ordering the part, I saw a couple of screws and it seemed like an easy task. However, I found that I had to remove to whole door first, which was actually easy. Then I started to remove the case. Then I removed several layers of a puzzle. Oven door had 3 pieces of glass and 3 metal brackets. The installation video was for a completely different oven. Although I got out the broken glass easily, I had difficulty reassembling. The oven diagram for the parts was even deceiving. I had to involve my spouse and after an hour of cursing everything, we finally managed to get the thing back together. Whoever designed this oven must have been a deranged German scientist. However, everything is back to normal and I probably saved a couple hundred bucks for a repairman.