GMC305PDS1 Whirlpool Microwave Oven Combo - Instructions

Several professional appliance repair people told me I had to get a new oven (double, no less!) because "they don't make that hinge anymore." That would have been a $4-5K investment to replace two ovens that both work fine. I'm not generally a DIY person, but was inspired by a FB page I follow called "Handy Women." I got the model number out of my oven, googled "replacement hinge for ____," and found it on this site right away. $120 and about 1 week later I had my hinges. I found this video in the comments on this website that shows (without narration) exactly how to change the hinges.
https://www.youtube.com/watch?v=XzQuU2gZYhk
The only mistake I made that cost me some time had to do with the little pins you have to put into the hinge to remove and replace the oven door. They were missing from the old hinges, and it didn't occur to me to use the ones that were in the new hinges (hadn't unboxed when I started.) I used threaded bolts that were the right diameter and length. They slid right in, but then when I went to take them out, it was an ordeal with WD-40 and an Allen wrench. Then it still didn't occur to me to look at the new ones, so I went to the hardware store and bought two more things the right size without threads. Of course when I took the new hinges out of the boxes they already had the little pins in them. Annoying and time consuming rookie mistake, but my oven door now closes just fine, and I'm getting a ridiculous amount of satisfaction from my little repair job!

The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.

Removed locking device

Removed the door from oven removed screws from door and replaced the old hinges with new ones perfect match

Unplugged old element unit and plugged in new element. Took two needle nose pliers and a flexible body. Took about 5 minutes. Works fine. Anybody can do it. Make sure power is off at the box.

Followed suggestions from prior Customers that had same problem.

Small, older female with limited hand strength here. Turned off the power to the stove. Removed the baking element from the oven wall with a screwdriver, snapped out the old one and snapped in the new one. 5 min tops. The broiler was a bit more labor intensive as the rusted and/or stripped screws did not want to come out. Used some liquid wrench, gripping grit, and a power drill to remove, but once the screws were out, it was another easy snap off/snap back in process. Had some screws on hand to replace the stripped ones. Broiled a steak that night with the new red hot broiler. So happy. This repair just saved me approximately $1800 to replace a 28 yr old drop-range. Very happy with this purchase.

I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.

Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

Removed door to see what happened to the spring, ordered new spring and door frame on line and replaced parts. Had to replace door frame as it broke while removing it.

Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven