RM973BXST0 Whirlpool Microwave Oven Combo - Instructions

Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.

My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!

I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.

Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!

Super simple, and the part arrived less than 48 hours after buying it online. I turned off the breaker to the oven and unscrewed the burner at the bracket holding it to the back wall of the oven. After pulling out the wires, all you do is tug at the two connectors and they detach. Just slide the new burner's connectors in, then screw it back into place. My arms aren't quiet long enough to reach all the way back there, so I got my son to help and I held the flashlight for him. Had it done before my husband got home from work!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then reverse the process and bingo ...done

EXTREMELY fast shipping of product ...I have purchased other products and always satisfied .

removed the two screws that hold the element in place, then slowly pulled the element out and disconnected the two wires, then reconnected the wires and screwed it back in - I'm a 25 year old female and did this in less than 5 min. - don't wait any longer to fix your oven!

my wife took the old element out i used a screw driver to remove it...i then ordered the new part using this web site...i then let my wife install the new element she then attatched the wires she used her fingers to tighten the bolt....and she is very very impressed with herself.

Turned off circuit breaker for oven. Unscrewed the 2 screws that held the element in place on the back wall of the oven. Save those screws! Pulled the element out from the wall. Disconnected the 2 wires. Attached the wires for the new element and then screwed the new element into the back wall. Flipped the circuit back on and the oven was fixed.

I read other repair stories before I completed the instillation and let me tell you that in it's self was a great help.

Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.

Part was on order and I still received it within three days.

You guys are the best, I recommend the site to all of my friends and family.

Shut off power to the stove.
I removed the screw that held the block in place. Then I lifted the top of the rage to get to the wires. I cut the wires from the old block and stripped back the insulation. Next I put the heat shrinking sleeve on. I attached the new block with the wire nuts, pulled the sleeve down and used a hair dryer to shrink them. Then you just hook it back on screw it in and your done.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.

turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.

I removed the block, cut and spliced the wires to the new block and installed the burner. I used the new style block kit and saved about $30. It worked great!