RM978BXPW1 Whirlpool Microwave Oven Combo - Instructions

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

Not only it was easy to install but to find them was even quicker, thanks to Part Select.com. After searching for quite some time I found the site and my problem was solved. Item was received in a timely manner and replacing was very quick.
Thank you.

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

Replaced with the new burner works like new. Thanks a bunch!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

Before ordering any parts I remembered seeing a fan above the nylon roof of the microwave. I had seen a belt that drove it on a prior repair 3 years ago.

I then removed 1 screw holding the electrical panel so I could tilt it open. Since power was still plugged in I didn't put my hand in. I used a flashlight and the broken belt.

I could also see the moter that turned the belt and tested it by starting and stopping the microwave and could see the motor pulley spin when it slowed to a stop. I then closed the control panel and screwed it in place.

That confirmed I proceded to go to the internet with the model # for the rane/microwave and looked for parts.

I had an easy job looking the part and saw that the fan as I had called it was named Stirrer because it kept stirring the microwaves over the food.

Overall I looked at 2 venders and chose Part Select because they showed the same catalog page and part numbers, and they had a better price.

I had my part/ belt in 4 working days and installed the new belt in about 15 minutes. This time unplugging the range so there was no power to be concerned with. It was a matter of picking out the old belt and putting the new belt on the motor then walking the belt over the large pulley at the Stirrer since the belt will stretch a bit.

Buttoned it up and later tested with popcorn and it left only a small amount of old maids.

Thanks, Walt

pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.

Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.

The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!

Removed old element, replaced new element. Unfortunately, this didn't fix the problem. It was the temperature sensor. But now I have a new bake element, though!

1. Turn off oven.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair