RM955PXPW1 Whirlpool Microwave Oven Combo - Instructions

As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!

was very easy to install I only needed a phillips screwdriver to remove old part and install new one.

Removed block (1 screw) Cut 2 connecting wires. Strip insulation. Attach new block with wire nut(per enclosed instructions) Heat shrink wrap with Lighter. attach block. 10 minutes: problem solved

I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:

Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connected them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.

The new handle, braces and screws arrived as quoted. My son-in-law installed the new one without much trouble. The handle is black and matches the black front of my stove. The older handle was sort of a wood-brown. Thus I like the new one better. Thank you for good service and prompt attention to the problem.
Linda Archibald
Hanson, MA

I followed the instructions provided.

Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!

First, my son pulled the range out and I unplugged it. Then he removed the 2 screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the wires. Then he placed the new element in the oven, connected the wires and put in the screws back in. It worked immediately!!

i just unpluged the old burner and slideed the new burners in place and they work great now like a new range

I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!

Removed the 2 screws that hold the element in place. Pulled the element forward about 3 inches and disconnected the two wires. Plugged the wire clips onto the new element and pushed the element back into place. Put the 2 screws back into place. This was a very easy repair.