RM955PXKW0 Whirlpool Microwave Oven Combo - Instructions

Unwrapped package. That was the hardest part. Inserted into the little spot on top of stove. Tested. Worked great!

Turn off the power, removed the two screw (needed a wrench to help turn screw driver at first). Pulled the element forward to expose the wire connectors. Removed connectors from the old element. iInstalled new element to the wire connectors (slide on), screwed plate back into oven. Turn on power and tested

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

First I checked to make sure the power was off with an electrical meter (wiggins). Next I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then pulled off the 2 wires replaced the element and put the 2 wires on the new element. I screwed it back into place and tested the element. When I turned the oven on my new element began to glow red and the repair was now complete. Super easy.

First I unpluged the stove, then I removed the two screws that hold the heat element in place. Then I pulled the heat element out a couple of inches and disconnected the two wires.
I just plugged in the new element wires, pushed the element in place and replaced the screws.
It only took about 10 minutes at the most.

Now I know why everyone said "less than 15 mins" for installation time...because "less than 5 min" wasn't an option! Went exactly as everyone described, just more quickly - turned off breaker, removed two screws, disconnected wires, reconnected wires to new element, re-attached it with screws, turned on breaker, checked it - worked like a charm. It was more work opening the box! Would have taken less time if my flashlight hadn't rolled off the open oven door leaving me with poor lighting conditions.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
then I reconnected the two wires to the new element and put back the two screws that hold the element in place and the job was finished.

I read other repair stories before I completed the instillation and let me tell you that in it's self was a great help.

Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.

Part was on order and I still received it within three days.

You guys are the best, I recommend the site to all of my friends and family.

Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.

Ordered acording to range model & such. Had ben unsucksessful gettin the right size thru the years & finally got the correct ones.

Replaced the element. The part came the next day which was great. Good customer service!

We have had our Whirlpool oven for 22 years and became very concerned that a part would not be available. We were thrilled to find the part as well as install the new part ourselves. With a screw driver, we disconnected the old baking element ( be sure to shut the power while doing this) and screwed in the new one. That simple!!!

I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.

The hardest part was figuring which breaker controlled the oven because it wasn't marked in my breaker box (it IS now!). So, first I killed all power to the stove, then unscrewed the 2 screws in the back of the oven holding the element. Pulled the element forward, then dissconnected the 2 clampy connector wires (yes, I'm a girl, no correct electrical jargon here). These were a little difficult because my oven is 21 years old & this is the first replacement I've had to do. I reconnected the new element clamps(which was easier), pushed the wires back through the opening & reinserted the screws. Threw the breaker back on, turned on oven to 200 degrees & let heat until the set temperature light turned off as a test. Voila - oven fixed!

Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.