RM988PXVM3 Whirlpool Microwave Oven Combo - Instructions

Super simple, and the part arrived less than 48 hours after buying it online. I turned off the breaker to the oven and unscrewed the burner at the bracket holding it to the back wall of the oven. After pulling out the wires, all you do is tug at the two connectors and they detach. Just slide the new burner's connectors in, then screw it back into place. My arms aren't quiet long enough to reach all the way back there, so I got my son to help and I held the flashlight for him. Had it done before my husband got home from work!

I read other repair stories before I completed the instillation and let me tell you that in it's self was a great help.

Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.

Part was on order and I still received it within three days.

You guys are the best, I recommend the site to all of my friends and family.

removed the two screws that hold the element in place, then slowly pulled the element out and disconnected the two wires, then reconnected the wires and screwed it back in - I'm a 25 year old female and did this in less than 5 min. - don't wait any longer to fix your oven!

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

Turn off the power, removed the two screw (needed a wrench to help turn screw driver at first). Pulled the element forward to expose the wire connectors. Removed connectors from the old element. iInstalled new element to the wire connectors (slide on), screwed plate back into oven. Turn on power and tested

Easy unplug appliance take racks out unscrew two screws gently pull out element unplug two wires put new one in reverse .

First, turn the breaker off to the oven, you don't want to electrocute yourself. There are two screws that hold the element to the back wall of the oven, undo those and pull the element towards you. There are two terminals at each end of the element, take these off, then reattach to the new element and screw back in to the back wall of the oven. This process takes maybe all of five minutes

remove all element that is held with two screws and install the new one. easy fix! and a lot cheaper than a new stove!

my wife took the old element out i used a screw driver to remove it...i then ordered the new part using this web site...i then let my wife install the new element she then attatched the wires she used her fingers to tighten the bolt....and she is very very impressed with herself.

Turned off circuit breaker for oven. Unscrewed the 2 screws that held the element in place on the back wall of the oven. Save those screws! Pulled the element out from the wall. Disconnected the 2 wires. Attached the wires for the new element and then screwed the new element into the back wall. Flipped the circuit back on and the oven was fixed.

We have had our Whirlpool oven for 22 years and became very concerned that a part would not be available. We were thrilled to find the part as well as install the new part ourselves. With a screw driver, we disconnected the old baking element ( be sure to shut the power while doing this) and screwed in the new one. That simple!!!

It was as easy as removing two screws, disconnecting two wires and replacing the new element. Piece of cake

First, I removed the oven door by pulling it open to where it loocked and then I pulled it up and off the hinges. Second, I removed the two screws on the top of the door and three screws on the bottom ot the door which allowed me to remove the front of the door. Third, using a nut driver, I removed the frame holding the inner glass to the door and removed that. Fourth, I removed the frame holding the broken glass to the door by removing the screws using my nut driver. I carefully removed the broken glass and vacuumed the channel that had the gasket in it. The gasket was fine so I did not have to replace it and will return it. I placed the glass in the frame on the gasket and reassembled the door in reverse order of how I had disassembled. All went smooth as silk.

I'll tell you.......PartSelect said the items would take from 3-5 days.....I got them in 48 hrs. I turned the breaker to the oven off. I unscrewd two screws from the back of the oven and pulled the element out and took it off of two connectors. Repeated the same with the broiler element. Job done saved $200.00...Job was quoted at $259.00

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.