Models > GMC305PDQ08 > Instructions

GMC305PDQ08 Whirlpool Microwave Oven Combo - Instructions

Jump to:

All Instructions for the GMC305PDQ08
106 - 120 of 235
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Kristen from Yorba Linda, CA
Parts Used:
W11373838
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Missing turntable
Ordered the part and was extremely pleased with how quickly it shipped and also the packaging was extremely secure. Will definitely purchase from this site again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Monty from Mansfield, TX
Parts Used:
W10642989
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Replace turntable motor
removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ravi from Lakewood, OH
Parts Used:
WPW10207397
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The bottom heating element of the wall oven burned out and needed replacement.
You will need a screwdriver and two pieces of duct tape (very important) before you start.
Unscrew the plate that attaches and keeps the element in place to the oven wall. If the screws are rusty, replace those too at this time.
Very gently pull the element and the wires out into the oven cavity. Do not tug. Gently remove one wire from the burnt element and use a piece of tape to stick it to the oven wall. If you lose the wire or if it slips back into the hole in the wall, you are in trouble. Repeat with the other wire. Now assemble the new element in the reverse order, one connector at a time. Screw back the holding plate, and you are done. Takes less than 10 minutes to complete and your oven will be as good as new.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Calvin from GARNER, NC
Parts Used:
WP9759243
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
E1 and e15
Removed locking device
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leroy from SUWANEE, GA
Parts Used:
WPW10207397
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The video gave me the confidence to order the part
The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nadine from ALACHUA, FL
Parts Used:
WP9759243
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
After using self cleaning feature oven wouldn't heat
I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Duane from COON RAPIDS, MN
Parts Used:
WPW10016550
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
replaced lower blower of a double wall oveno
Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from FRISCO, TX
Parts Used:
WP9759641, WP4451722
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken glass oven door
Followed suggestions from prior Customers that had same problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
LAURIE from BILTMORE LAKE, NC
Parts Used:
WPW10131825
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The oven was over heating because it wasn’t reading the temperature
Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenyon from CALHOUN, GA
Parts Used:
WPW10207397
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
The element had burned up.
Unplugged old element unit and plugged in new element. Took two needle nose pliers and a flexible body. Took about 5 minutes. Works fine. Anybody can do it. Make sure power is off at the box.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jay from MINNETRISTA, MN
Parts Used:
WP9759243
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Limit Thermostat had burned out due to high temp of self cleaning mode
1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Elizabeth from HOUSTON, TX
Parts Used:
WP8203546
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
nancy from edison, NJ
Parts Used:
WP4449259
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
glass on oven door was broken
removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Ladson, SC
Parts Used:
W11193483
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
The light in our microwave was out.
We had to remove screws from the vent covers above and below the microwave, then there were 2 screws (one on each side) that attached the microwave to the oven. Once all of the screws were removed we had to pull the microwave out. Then we pulled the light cord out, removed the burnt out light and installed the new one. Then reversed the steps.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Oxnard, CA
Parts Used:
W11373838
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken cooking tray
Replaced the glass tray
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GMC305PDQ08
106 - 120 of 235