GMC275PDB0 Whirlpool Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- KEVIN from HOUSTON, TX
- Parts Used:
- WP4449253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The oven in the demo video did not have an interior set of screws holding in the exterior glass
Watched the repair video and started the project. Ran into a problem when trying to remove the interior panel off the door to reach the broken interior glass. On this model Kitchen Aid there is another section that is screwed in holding the exterior glass pieces in place. It prevents the interior panel from coming off the front of the oven door. So we had to flip over the door and unscrew the glass retaining bars to get the interior panel off and reach the glass. This allows the entire door to come apart in pieces so you have to carefully line up everything to re-assemble the door. Part of the issue with this is some of the retaining screws are not very long so you have to press the pieces back together to make sure the screw will catch in the original hole. We had to do this twice to ensure the interior door glass was laying flush on its mounts. A bit fiddly for sure, and if I was working alone it may not have been successful. But at least we know how the door is put together!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from PLANO, TX
- Parts Used:
- WP4449253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The interior glass broke when I tried to wipe hot glass with a cold washcloth
I watched the video on the product page and followed it step by step. Not difficult at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Bloomington, IN
- Parts Used:
- WP9760767
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The element connector broke on the element
I shut the power off first as this is 240v. Then removed all the screws that hold the element on. The old one had 5 screws. For this part you will need to buy new or reuse the old screws. I reused the old ones. Once loose the element pulled forward and exposed the connectors. I used pliers to pull the broken one out as it did not come out with the old element. It will only pull out a few inches, but that is enough to unplug the connectors. After unplugged the element can be taken to recycling. The new one can be set in the oven with the connectors near the wires and plug the two sides into the connectors. Have a screw ready and slide the rear of the element back into rear which will support it while you insert one of the screws into the front support to hold the element in place. Then move the element and support as needed to install the remaining screws. Once it is all tight, turn on the power and make sure it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kati from Henrico, VA
- Parts Used:
- WPW10207397, WP9760767
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Elements went out in the oven
Small, older female with limited hand strength here. Turned off the power to the stove. Removed the baking element from the oven wall with a screwdriver, snapped out the old one and snapped in the new one. 5 min tops. The broiler was a bit more labor intensive as the rusted and/or stripped screws did not want to come out. Used some liquid wrench, gripping grit, and a power drill to remove, but once the screws were out, it was another easy snap off/snap back in process. Had some screws on hand to replace the stripped ones. Broiled a steak that night with the new red hot broiler. So happy. This repair just saved me approximately $1800 to replace a 28 yr old drop-range. Very happy with this purchase.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from BELLEVUE, WA
- Parts Used:
- WP8303555
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace broken part
Installed new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from ORANGE, CA
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Ladson, SC
- Parts Used:
- W11193483
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The light in our microwave was out.
We had to remove screws from the vent covers above and below the microwave, then there were 2 screws (one on each side) that attached the microwave to the oven. Once all of the screws were removed we had to pull the microwave out. Then we pulled the light cord out, removed the burnt out light and installed the new one. Then reversed the steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Waterloo, SC
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken inside oven door glass
We followed the instructions given by Parts Service. The only problem we had (Whirlpool left two screws out of spacer bracket and it fell out requiring further removable of inner glass to replace spacer. Process took about twenty minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Phoenix, AZ
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass tray missing
found the part no. and ordered it. it was delivered fast and efficient.
tracking was also helpful.
thanks
tracking was also helpful.
thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Concord, CA
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass dish for microwave
no repair needed - ordered part, came within 3 days - very satisfied
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Navid from Dunn Loring, VA
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Microwave cooking glass broken
Easily replaced after received the product from Part Select. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from HINSDALE, IL
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old microwave glass tray shattered while warming a hard-boiled egg.
I took the new tray out of the box and placed it in the microwave oven.. No tools needed.
Was this instruction helpful to you?
Thank you for voting!