RM278BXP0 Whirlpool Microwave Oven Combo - Instructions

Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.

Funny, I suppose. We decided to buy a new stove given the old age of the old one. Problem is, on delivery day it wasn't delivered and we discovered that there wasn't even one in the warehouse. At that point we got ticked and decided to look into the problem. The website led us right to the problem. We ordered, the part arrived the next day and the replacement was simple. Just unscrew the holder inside the over, unplug the old element and plug in the new. I needed needle nose pliers because one of the wires slipped behind the insulation. We also bought a thermometer and found that the calabration was right on the money. Happy campers... we saved $400.

Found breaker box and shut off power to stove, Check to make sure you turned the right breaker off before you attempt to put you hands in it, also make sure all the switches on the stove are in the off position . Open Oven Door, I used a Phillip screw driver to remove the two screws holding the Bake element in place . pull out to reach wire connections and gently pull connectors from element. Remove the old Bake element and Install the New one,by reversing process in removing the old one. after you have it back in place turn breaker back on at breaker box turn oven control to Bake setting, turn Oven Temperature control to around 200 degrees and Element should began to glow bright orange, job complete, it's that easy!~

My handyman removed the old burnt our element by removing two screws and disconnected two wires and reconnected wire and screwed the unit into the oven wall. This repair was a breeze! Thanks for making my life easier!

1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!

I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. It was that easy. But the people at PartSelect.com were the ones that made it easy; easy ordering and prompt shipment. I got he part in approximately three days. Thanks PartSelect.com. You made me and my wife very happy. We didn't think we were going to have the use of an oven for Christmas. You came through for us.

I removed the two screws that hold the element in place and then I pulled the element out and slid off the contacs and it was disconnected in less than two minutes. When it arrived I installed the new one the same way in less than 2 or 3 minutes and while I waited for thepart to arrive I got a chance to clean my oven and so all is well, I am very pleased with my purchase. It is just that easy and I am happily baking again. Thanks, j. Cale, morrow ga.

Very easy, thanks for the great support

Removed the retaining plate screws (Phillips), pulled out the element enough to disconnect the wires, disconnected the wires. Installation was the reverse.

btw, PartSelect shipping was phenomenally fast. I ordered this part on Saturday and it was at my door at noon on Tuesday!! Holy Moly...

The repair was simple. Two screws and it popped in. The part arrived quicker then expected. Done in no time.

Grabbed my courage with both hands, then with my other hand I used a screwdriver. Delicately removed 2 screws holding the broken element. Once that delicate operation was done, I took out the old and place the new. Once again grabbed the screwdriver and with agility replaced 2 screws. Then, I turned on the oven and Voila, ready to bake some enchiladas.
Winner, winner, chicken dinner.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
reverse to install.
It was great to find a place that has the parts you need, and supper fast delivery service.

Thank you Ed Andrews
sound, lighting, and video systems engineer.

removed the screws that held the element in place. Pulled out the element out about three inches and disconnected the two wires, put the new one in, did the reverse and done. the best part was I orderd it on line after 3:oopm on a thursday and the part was delivered by saturday morning- wow!

My husband undid the screws of the element. I went to Home Depot and they said I had to order in online. I could not find the part of the Home Depot website, so I googled the part and your business was easy to locate and order the part. It arrived in two days and I, the wife, was able to rescrew the element into place and, voila, the oven was functional again.

Turn power off, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new element, put screws back in and test.