GMC275PDS6 Whirlpool Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from LAGUNA VISTA, TX
- Parts Used:
- WPW10440740
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
This is a small halogen light bulb for the microwave. This is the third time it has had to be replaced.
This is the third time that the bulb went out.It took two Sears service technitions to remove the entire appliance out of the cabinet. The entire top has to be removed and the insolation has to be pulled back to get to the electrical wire. I am waiting for an appointment to get Sears to do it again. The door springs have broken and you have to make sure the door is closed before walking away. It has a heavy glass and the weight is pretty heavy. Robert.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from HIGH SPRINGS, FL
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bottom element not working.
Turned off breaker to oven. Removed 2 screws, used pliers to remove 2 wires from old element, replaced with new part, connected wires to new element and screwed in 2 screws. Turned on breaker, then oven and new element heated. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CARY, NC
- Parts Used:
- WPW10207397
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken heat element.
Replaced the lower heating element with a new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Black Mountain, NC
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Destrehan, LA
- Parts Used:
- WP9760767
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler Element quit working
Scarey> First thing you should do is cut off the electricity at the main breaker box. I dam near blowed myself up. It's 220Volt I found out after all hell blew up in my face. I was lucky and didn't get shocked.I shorted out the old broiler element.
So I made the job real easy I called a professional to come install the new broiler element.
I suggest you put a big red paper in each box that says turn off the power first. If your not sure how to do that call a pro.
So I made the job real easy I called a professional to come install the new broiler element.
I suggest you put a big red paper in each box that says turn off the power first. If your not sure how to do that call a pro.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joyce from thomasville, NC
- Parts Used:
- WP9759243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
every time I would try to do the self clean mode on my drop in range the thermostat blows. Last time it was still under warranty. I took the part number from the repair man's invoice to order the new part.
My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from SOUTHAVEN, MS
- Parts Used:
- WP9760588
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
oven light would not come on
cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from CLARKSVILLE, MD
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass Tray broke
Ordered a new one, put it in place in less than one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from SAUGUS, CA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original microwave turntable was cracked.
The replacement turntable we received was an exact duplicate of the original. It was as easy as rinsing the new turntable, taking the old turntable out and putting the new one in.
Was this instruction helpful to you?
Thank you for voting!
I had two issues, 1). The oven blower was making a lot of noise when the oven was turned on. 2). The microwave turntable wasn't turning.
The replacement of the blower was an easy repair. Just had to remove two back panels of the oven and the blower was then very accessable. Just remove the two electrical wires and then three screws and the blower came right off. Put the new blower on with the three screws and replaced the 10 or 12 screws holding the back panels and the job was complete!. The difficult part of the job was removing the combo unit from the cabinet to access the back panels. That part took some effort. Had to build a platform to slide the oven out onto after I disconnected the electrical feed wire (#6 wire) located in a junction box in my attic. Once that was done, the actual blower replacement was simple. The turntable motor was a different story...Although replacing the turntable motor was going to be as easy as replacing the blower motor, I couldn't access the underside of the microwave without disassembling the whole combo unit cabinet! That was very disappointing to me that Whirlpool didn't make that part easier to access, so I didn't replace the turntable motor. Too bad but we are just going to live with the turntable not turning!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUMMERVILLE, GA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked glass tray
Part arrived in timely manner and placed it in microwave oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Minden, NV
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass microwave tray broke
Set the new one inside the microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from TINLEY PARK, IL
- Parts Used:
- WPW10131825
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven will not maintain set temp
Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roxanne from MARTELL, NE
- Parts Used:
- WPW10207397
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Had to replace the bake element
Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles R from Libertyville, IL
- Parts Used:
- W10245183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Loud buzzing noise and no heat.
PartSelect website indicated replacing the high voltage power supply diode is the solution for "no heat" 99% of the time, but the diode was OK. There is more info at the website concerning the case of "loud buzzing and no heat" indicating the magnetron needs to be replaced. As an electrical engineer with knowledge of microwave components, this was also my best guess. However, getting to the magnetron is not the easiest job, but it's not impossible. You also have to be careful to bleed off any charge stored on the high voltage power supply capacitor. Luckily, I found my KitchenAid service manual tucked away inside the unit since I couldn't find it online.
Was this instruction helpful to you?
Thank you for voting!