57-5709-10-03 Tappan Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MOBILE, AL
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
When oven was set at 400, actual temp would run about 285.
1 Turned off the oven breaker.
2. Removed the oven racks.
3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.
4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.
5. Installed the new sensor and now oven holds temperature steady.
Easy order, quick delivery and easy installation, happy wife.
2. Removed the oven racks.
3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.
4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.
5. Installed the new sensor and now oven holds temperature steady.
Easy order, quick delivery and easy installation, happy wife.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from KALISPELL, MT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The elements were not heating up
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Shermansdale, PA
- Parts Used:
- 5303922044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turn Table Was Unable To Turn To Heat Food Properly And Thoroughly
I pulled out the glass turn table tray and put the bushing in the little whole, in the center of the bottom (under turn table tray). Fixed the problem right away. Working wonderful! Was happy with how easy it was to locate part. Had received this microwave as a wedding gift, feb. 1994. Thought I was going to have to replace. Thanks to your website I was able to locate and purchase the part needed to fix the problem in less than 1 minute. I thanks you. I love this particular microwave!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Little Silver, NJ
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Error Code F1
I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from FOREST HILLS, KY
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would start to heat then quit,checked the temperature sensor with ohm meter after cool down reading about 1100 ohms. I cleaned connection tried it again seemed to work well but quit again in just few days.
Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great
OEM parts plug in same, works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everette from HARRISBURG, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat. Didn’t cut off at set temp
Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.
Saved $150 on a service repair call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Falmouth, MA
- Parts Used:
- 5304409888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from addison, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven not reheating after initial heat up
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cherilyn from W HOLLYWOOD, CA
- Parts Used:
- 318345216
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No instructions needed
Just slide the rack into the oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from BIG SPRING, TX
- Parts Used:
- 318255101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking heat element burned out
Removed oven racks removed 2 screws & pulled the element forward & disconnected the old element by wiggling the snap on connecters put in new element connected the snap on wires pushed it back in place & put both screws back in done in 10-15 minutes ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from TEMPE, AZ
- Parts Used:
- 318255101
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Oven wasn't baking; broiler was OK.
1. Switched the oven power off.
2. Tried unscrewing the two screws in the rear of the oven but they were
too tight. Used a power screw driver to unscrew the bottom element. 3. Pulled element out and disconnected the two wires.
4. Attached the two wires to the new bake element and fastened it
with the two screws.
5. Switched the oven power on.
6. Tested the oven with good results!
2. Tried unscrewing the two screws in the rear of the oven but they were
too tight. Used a power screw driver to unscrew the bottom element. 3. Pulled element out and disconnected the two wires.
4. Attached the two wires to the new bake element and fastened it
with the two screws.
5. Switched the oven power on.
6. Tested the oven with good results!
Was this instruction helpful to you?
Thank you for voting!