57-2709-00-02 Tappan Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marie from Fairview Park, OH
- Parts Used:
- 318255101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element cracked in two pieces
First removed the two screws that hold the element in place.I then pulled the element out about three inches and disconnected the two wires. The new element was put in place and reconnected to the two wires.The two screws to hold the element in place wre put back in.Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from GAINESVILLE, GA
- Parts Used:
- 5304524341
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Shermansdale, PA
- Parts Used:
- 5303922044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turn Table Was Unable To Turn To Heat Food Properly And Thoroughly
I pulled out the glass turn table tray and put the bushing in the little whole, in the center of the bottom (under turn table tray). Fixed the problem right away. Working wonderful! Was happy with how easy it was to locate part. Had received this microwave as a wedding gift, feb. 1994. Thought I was going to have to replace. Thanks to your website I was able to locate and purchase the part needed to fix the problem in less than 1 minute. I thanks you. I love this particular microwave!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Falmouth, MA
- Parts Used:
- 5304409888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Manchester, TN
- Parts Used:
- 318255101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower heating element burned out
Take out 2 Phillips head screws.
Pull the element out, not disturbing the insulation any more than necessary.
Remove the 2 wires from the old element.
Discard old element.
Attach the 2 wires to the New element.
Feed the wires back through the insulation.
Replace the 2 Phillips head screws.
Turn on oven to test.
Done.
Pull the element out, not disturbing the insulation any more than necessary.
Remove the 2 wires from the old element.
Discard old element.
Attach the 2 wires to the New element.
Feed the wires back through the insulation.
Replace the 2 Phillips head screws.
Turn on oven to test.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from TEMPE, AZ
- Parts Used:
- 318255101
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Oven wasn't baking; broiler was OK.
1. Switched the oven power off.
2. Tried unscrewing the two screws in the rear of the oven but they were
too tight. Used a power screw driver to unscrew the bottom element. 3. Pulled element out and disconnected the two wires.
4. Attached the two wires to the new bake element and fastened it
with the two screws.
5. Switched the oven power on.
6. Tested the oven with good results!
2. Tried unscrewing the two screws in the rear of the oven but they were
too tight. Used a power screw driver to unscrew the bottom element. 3. Pulled element out and disconnected the two wires.
4. Attached the two wires to the new bake element and fastened it
with the two screws.
5. Switched the oven power on.
6. Tested the oven with good results!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie Laura from HOUSTON, TX
- Parts Used:
- 318255101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The bottom element of my wall oven stopped heating.
My neighbor came over to replace the element. The procedure was simple. Following the instructions given online, he turned off power to the oven, removed the screws holding the element, replaced the element, turned power back on, and now my oven works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from BIG SPRING, TX
- Parts Used:
- 318255101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking heat element burned out
Removed oven racks removed 2 screws & pulled the element forward & disconnected the old element by wiggling the snap on connecters put in new element connected the snap on wires pushed it back in place & put both screws back in done in 10-15 minutes ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cherilyn from W HOLLYWOOD, CA
- Parts Used:
- 318345216
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No instructions needed
Just slide the rack into the oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!