76-8667-00-07 Tappan Microwave Oven Combo - Instructions

Simple repair ,unplug unit,cut the 2 wires close to heating element,remove elements 2 screws w/1/4 inch nut driver. Cut and strip 2 wires back about 1/2 inch,be sure to cut wires close to element,wirenut both wires together. Reinstalled element,plug unit back in. Done . . . 12 Minutes,ready to bake a cake. .

First turn the thermostat off-cut the wires leading to the ignitor, close to the ignitor side-Remove the two 1/4" monting bracket screws and remove the ignitor install the new ignitor using the same 1/4" screws and reconnect the wires leading into the ignitor, note the polarity is not imp[ortant--use the heat temp-wire nuts provided--close the door and call for heat the gas valve is working fine now....

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!

Open the door and slide in the new rack.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.

Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.

Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.

removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since

Opened the oven, removed the bottom plate located the ignitor within arms reach, removed two screws and a snap out part. replaced with the new ignitor and put the stove bottom on and waala...DONE
I have ordered all my parts from Parts Select and have never had a problem. Thank you. Jody in Montana

pulled drawer out and took old igniter off and replaced it

After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!

first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done

had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you

AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.