57-2729-00-01 Tappan Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Northwood, NH
- Parts Used:
- 5303303047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Carousel Tray Drive Bushing Broke.
Just had to remove the carousel tray and replace the drive bushing. And we were back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tony from san antonio, TX
- Parts Used:
- 5303303047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carousel bushing broke,no more spin,burnt food.
Finally figured out after many months that all I needed to do was to get online and order the part. Part quickly arrived and within seconds I was back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Miramar Beach, FL
- Parts Used:
- 5304497424
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
not heating as setting reads
watched u tube sent by your company, opened back of oven,removed sensor,checked w/ohm meter,ordered part, replaced sensor,replaced back on oven, DONE! works like new amazing help I was given by your staff! I was quoted over $200.00 to come to my house,ck.,fix, and part replaced. My cost was $50.00 + shipping of $7.00. Thank you guys!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Lakewood, OH
- Parts Used:
- 5304497424
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gas Oven Overheating
Removed cover on back of range (four screws held it in place), removed screws holding the oven sensor in place, pulled out oven sensor and disconnected the snap-like connection, tested with ohm reader (was below 1000 and 1100), ordered new part (came next day), inserted the sensor, screwed it back in, snapped the connectors together, replaced cover on back of stove. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Gosport, IN
- Parts Used:
- 5303091004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One wheel on the roller tray had a blow-out
Trashed the old roller tray and put the new one in. Fast shipping, and dependable company to do business with. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Starr from Knoxville, TN
- Parts Used:
- 5303303047, 5303091004
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
tray turntable piece broke
WELL, I ordered 2 of the tray drive bushings, thank God, because 1 shaft was too short. AND wouldn't even reach the glass tray, although part numbers were identical. So, I took the old broken drive bushing and sanded off the broken end, turned it upside down and glued the new bushing to it. Reaches the glass tray perfectly now, and as long as I don't put overweight bowls of water etc on it, it may last longer this time,, the drive bushings don't really go on the gear as well as they should-length wise- and any weight that stalls the turntable puts a tremendous strain on the plastic notched part of the bushing shaft
Was this instruction helpful to you?
Thank you for voting!