MER6750ACQ Maytag Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joel from Dillon, SC
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
burner not as hot as it should be
I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from West Lakeland, MN
- Parts Used:
- W10823709
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dual burner (front right) not fully working
The dual burner on my range wasn't working—the inner, smaller portion would heat up, but the outer portion (for larger pots/pans) would not. I searched online and discovered that the element is easily replaced, and Yay! It was! I had difficulty finding the model number of my range, as it wasn't in any of the obvious, suggested places. I had to get help to slide my range away from the wall (which was the most difficult part of this project!), but in doing so, found a metal tab on the back of the range, near the top, that flipped up to reveal the model and serial #s! From that info, I was able to find and order the correct replacement element for the burner that wasn't working, and in less than an hour, had it fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAHN T from SAN MARINO, CA
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I Order 2 Switches For 8" Heating Element
Turn off power 220v, opened cook top, remove old 8" switch and replace with one of the new switch ps2089438. However, I have another cook top, it is a 6" heating element. Can I use the same switch for 8" and use on a 6" heating element? Since I order 2 new ps2089438 switches. Thank you for your anwser. Kahn lee
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fairmont, WV
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner would go to high when turned on
Pulled stove out to unplug. Removed screws holding end covers then remove screws on the underside of cover as you face the stove top.Remove knobs.Pull bottom cover forward and up so you can lift it off to see the insides.Remove wires and attach to the new part one at a time. Unscrew old from the front and attach the new one.Put it back together.Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni from Laurinburg, NC
- Parts Used:
- W10823709
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The outer edge of the burner was not working.
The repairs was really easy. All you had to do was remove the screws holding the glass top surface down, raise it up, then start by pulling one wire at the time and plugging it into the new element. Then bolt the glass top surface down and it was ready to use, good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Crestwood, MO
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken leveling leg.
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Herriman, UT
- Parts Used:
- W10823711
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner not heating up
first I checked continuity through the surface element (burner) switch (rheostat) which was fine. then found the screws holding the burner top on and removed, this made it possible to lift up the burner top and remove the burnt out surface element.which was easy to see. take down the number, buy a new one and re hook up the four wires to the new element. (always mark down where the wires went)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruben from Port St Lucie, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rear left burner,went out.
I did exactly what your instruction video showed. The most important thing to remember is to TURN THE POWER OFF FIRST.
Was this instruction helpful to you?
Thank you for voting!